User manual YAMAHA CP-70M

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] Decoders that can be used with a sound field program · PLIIx Movie (PLII Movie) · Neo:6 Cinema Note · The following MOVIE sound field programs cannot be used with a surround decoder. ­ Mono Movie ­ Sports ­ Action Game ­ Roleplaying Game 5 Press oCursor k / n to select the parameter that you want to change, and press oCursor l / h to change the parameter. An asterisk (*) appears on the left of the sound field parameter name displayed on the monitor when you change the parameter from its default setting. For details on functions and adjustable ranges of the sound field parameters, see "Sound field parameters" on this page. y · Repeat steps 4 and 5 to change other sound field program parameters. · A complete list of the parameters of some sound field programs may exceed one page. In this case, press oCursor k / n to scroll through pages. 6 To end the edit, press mSETUP. Setting sound field parameters Although the field sound programs would satisfy you as they are with the default parameters, you can arrange sound effect or decoders suitable for acoustical conditions of sources or rooms by setting the parameters (sound field elements). y · You can protect the sound field against the changes of parameters the sound filed parameters when "Memory Guard" of the setup menu is set to "On" (see page 56). To change the parameters, set it to "Off. " To initialize the parameters of the selected sound field program, oCursor n repeatedly to select "Initialize" and then press, oCursor h. When the confirmation screen appears on the monitor, press oCursor h to confirm the initialization or oCursor l to cancel it. Sound field parameters y · The default settings are marked with "*. " CINEMA DSP basic parameters DSP Level Adjustable range: -6 dB to 0 dB* to +3 dB 1 2 3 Turn on the video monitor connected to this unit. Press oCursor k / n to select "DSP Parameter" and press oENTER. The larger the value, the later the reverberation sound begins. Increasing the value of Rev. Delay allows you to create a reverberant sound in a wider area for the same Rev. Time. Level (dB) Source sound 60dB Level Level Reverberation Time Time Rev. Delay Rev. Time Time Small reflected sound Large reflected sound Small = 0 Large = 10 Parameters for adjusting reverberant sound Parameter Adjustable range 1. 0 to 5. 0s 0 to 250ms 0 to 100% Rev. Time Rev. Delay Rev. Level 48 En Editing surround decoders/sound field programs Rev. Level parameter adjusts the reverberation sound level. Increasing the value of Rev. Level makes the reverbration sound level higher, which allows you to create more echo. Source sound Level Decoder parameters You can customize decoder effects by setting the following parameters. When PLIIx Music/PLII Music is selected INTRODUCTION Panorama Choices: Rev. Level (dB) Off*/On Adjusts the soundscape of the front sound field. Sends stereo signals to the surround speakers as well as the front speakers for a wraparound effect. Dimension Adjustable range: -3 to STD* to +3 Time PREPARATION Parameters only usable in certain sound field programs 2ch Stereo only Direct Choices: Auto*/Off Adjusts the difference in level between the front sound field and the surround sound field. You can adjust the difference in level created by the software being played back to obtain the preferred sound balance. The surround sound gets stronger as you make the value more negative and the front sound gets stronger as you make the value more positive. BASIC OPERATION Automatically bypasses the DSP circuit and tone control circuit when an analog sound source is selected as the input source. Auto Outputs sound by bypassing the DSP circuit and tone control circuit when the "Bass" and "Treble" tone controls are both set to 0 dB. Off Do not bypass the DSP circuit and tone control. 7ch Stereo only Center Width Adjustable range: 0 to 3* to 7 You can spread the center sound toward left and right according to your preference. Set this parameter to 0 for outputting the center sound from the center speaker only, or to 7 for outputting it from the front left/right speaker. [. . . ] 25 Selecting SCENE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Setting remote control code . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Setting the Parental Lock, SIRIUS satellite radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Set-top box connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]