User manual YAMAHA CP-80D

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] You can adjust the difference in level created by the software being played back to obtain the preferred sound balance. The surround sound gets stronger as you make the value more negative and the front sound gets stronger as you make the value more positive. ADVANCED OPERATION CT Width Adjustable range: 0 to 3* to 7 You can spread the center sound toward left and right according to your preference. Set this parameter to 0 for outputting the center sound from the center speaker only, or to 7 for outputting it from the front left/right speaker. When Neo:6 Music is selected ADDITIONAL INFORMATION C. Image Adjustable range: 0. 0 to 0. 3* to 1. 0 Adjusts the front left and right channel output relative to the center channel to make the center channel more or less dominant as necessary. APPENDIX English 37 En Operating various settings for this unit (Setup menu) You can call the setup menu using the remote control and change the settings of various menus. You can change the following settings in the setup menu. For details, read "Basic operation of the setup menu" first, and see the respective pages. Menu/Submenu Speaker Setup 1 Auto Setup (YPAO) 2 Manual Setup A)Config Sets items for speakers. Automatically adjusts output characteristics of speakers. Manually adjusts output characteristics of speakers. Sets speaker configurations, such as connection status of speaker and a size of the connected speaker (sound reproduction capacity), suitable for the listening environment. Separately adjusts volume of each speaker. One is "Auto Setup (YPAO)" for automatic adjustment and another is "Manual Setup" for manual adjustment. y · The default settings are marked with "*. " INTRODUCTION 1 Auto Setup Automatically adjusts output characteristics of speakers to obtain optimum balance for the output sound based on positions and performances of the speakers and acoustic characteristics or the room, which are automatically measured. For details on operations, see page 18. PREPARATION 1 HDMI y · You can return to the previous screen by pressing nRETURN. 2 Manual Setup Adjusts output characteristics of speakers based on manually set parameters. After Auto Setup (YPAO) is performed, you can check automatically adjusted parameters in the Manual Setup menu. Fine adjust the parameters for your preference if necessary. A)Config Sets speaker configurations, such as connection status of speaker and a size of the connected speaker (sound reproduction capacity), suitable for the listening environment. y · The speaker configuration includes items for defining a speaker size: Large or Small. Large and Small refer to speakers with woofer diameters 16 cm or larger and smaller than 16 cm, respectively. 3 To display submenus, select a menu that you want to set using nCursor k / n, and press nENTER. For example, the following screen appears when you select "2 Display. " BASIC OPERATION Dimmer;;;;;;;0 4 Select an item using nCursor k / n, and change the setting of the item using nCursor l / h. y · You can change other items by repeating step 4. ADVANCED OPERATION Bass Out Choices: SWFR/Front/Both* 5 y To finish the setting, press lSETUP. ADDITIONAL INFORMATION · When nCursor or other keys do not work after completing the menu, select the input source again using gInput selection keys. Selects speaker(s) for outputting low-frequency components of the LFE (low-frequency effect sound) channel or other channels. LFE channel signals Parameter Both SWFR Front Subwoofer Output Output Not output Front speakers Not output Not output Output Other speakers Not output Not output Not output APPENDIX English 39 En Operating various settings for this unit (Setup menu) Low-frequency components of other channel signals Parameter Both SWFR Front [1] Subwoofer [1] [4] Not output Front speakers [2] [3] [1] Other speakers [3] [3] [3] Small Large y Select this when small surround speakers are connected. [. . . ] 10 Surround right speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 SWFR, C)Distance, speaker setup . . . . . . . . . . . . . . . . . 41 V VIDEO jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Video jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 VIDEO jack, front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Video/audio jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Virtual CINEMA DSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 VOLUME +/­, remote control . . . . . . . . . . . . . . . . . . . . . . . . . 7 VOLUME control, front panel . . . . . . . . . . . . . . . . . . . . . . . . . 4 VOLUME indicator, front panel display . . . . . . . . . 6 Volume Trim, OPTION menu . . . . . . . . . . . . . . . . . . . . . . . 33 Y YPAO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 YPAO, troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 T The Bottom Line, sound field program . . . . . . . . . 25 The Roxy Theatre, sound field program . . . . . . . . [. . . ]