User manual YAMAHA CRW2100SX

[. . . ] FCC INFORMATION COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: Fax: Type of Equipment: Model Name: Yamaha Corporation of America 6600 Orangethorpe Ave. Buena Park, CA 90620 714-522-9011 714-228-3913 CD Recordable/Rewritable Drive CRW2100SX This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] Press the button above the window to decrement the SCSI ID number, or the button below the window to increment it. (P. 12) SCSI connectors Connect either of these to your computer's SCSI card using the SCSI cable. The other connector can be used as a pass-through when daisy-chaining more SCSI devices to it. It can be left vacant if your drive is the last device on the SCSI chain and is terminated. (P. 20) Serial number sticker This consists of 3 letters and 7 digits. You may need to refer to this number when requesting User Support services. (P. 11) 8 Setup Flowchart These flowcharts show the procedure for setting up the CRW2100SX drive. For easy cross-referencing, the relevant pages in this manual are also given. Windows Users STEP STEP 1 STEP Do you have a SCSI card? YES NO 1-1 Purchase a SCSI card Recommended models: Adaptec AHA-2940-series (PCI) 2 STEP Check that the SCSI card is recognized correctly (P. 22) STEP 1-2 Read this manual and insert the SCSI card into the appropriate PCI slot on the computer. Install the SCSI card 3 STEP Set up the CRW2100SX drive 1. Set the switches at the rear of the drive. Connect the SCSI and power cables, then switch the drive on. (P. 18-20) 4 STEP Check that the CRW2100SX drive is recognized correctly (P. 22) Install the CD writing software For details about how to install the software, refer to the documentation that came with it. 5 STEP 6 Start using the CRW2100SX drive! Use the drive to create audio CDs, to back up data on your hard disk, or for whatever purpose suits your needs. 9 Setup Flowchart Macintosh Users STEP 1 STEP Does your Macintosh have a built-in SCSI connector? YES STEP NO 1-1 Purchase a SCSI card Recommended model: Adaptec PowerDomain 2930U (PCI) 2 STEP Set up the CRW2100SX drive 1. Set the switches at the rear of the drive. Connect the SCSI and power cables, then switch the drive on. (P. 18-20) STEP 1-2 Read this manual and insert the SCSI card into the appropriate PCI slot on the computer. Install the SCSI card 3 STEP Check that the CRW2100SX drive is recognized correctly Use the Apple System Profiler and check that the drive is recognized correctly. 4 STEP Install the CD writing software For details about how to install the software, refer to the documentation that came with it. 5 Start using the CRW2100SX drive! Use the drive to create audio CDs, to back up data on your hard disk, or for whatever purpose suits your needs. 10 Setup Procedures Serial Number Once you have taken the CRW2100SX drive out of its packaging, you should immediately note down the serial number found at the rear of the drive under the bar code. You may need to refer to this number when requesting Customer Support services. In the box below the following diagram, write down the 10character serial number (consisting of 3 letters followed by 7 digits). Serial number (3 letters and 7 digits) Serial No. SCSI Settings Before connecting your CRW2100SX drive to your computer, you need to set up the drive using the switches located at the rear of the unit. You'll need to set the following: q SCSI ID number q Termination 11 Setup Procedures 1 SCSI ID number Each of the SCSI devices connected to the computer is identified by its SCSI ID number. You need to assign a number from "0" to "7" for each SCSI device. Commonly, ID number "7" is reserved for the computer's SCSI card itself. Therefore, your CRW2100SX drive can actually be assigned an ID number from "0" to "6. " Press the top or bottom button of the CDR ID selector switch to decrement or increment the SCSI ID number, as shown below. Press to decrement SCSI ID number SCSI ID number Press to increment SCSI ID number n The SCSI ID number for each device on the chain must be unique. Make sure the CRW2100SX drive's SCSI ID number is not the same as that of any other device on the chain. By factory default, the CRW2100SX is assigned ID number "1" but this can be changed. 12 Setup Procedures 2 Termination Terminators prevent SCSI signals from being reflected off the last device in the chain. [. . . ] 8, 13 Track-at-Once (TAO) . . . . . . . . . . . . . . . . . . . . . . . . . . 29 F firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 H Headphone jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]