User manual YAMAHA CRW2200E WITH SCSI-CONNECTOR FIRMWARE FOR WINDOWS95 98 98SE ME NT4.0 2000 XP

[. . . ] IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. [. . . ] 20, 28) 1 ID SELECT jumper switches Set these switches using black plastic shunts in order to manually assign a SCSI ID number for the drive. 2 PARITY jumper switch Set this switch using a black plastic shunt in order to enable parity checking. 3 TERMINATOR jumper switch Set this switch using a black plastic shunt in order to enable the drive's built-in SCSI termination. 4 BLOCK SIZE jumper switch Set this switch using a black plastic shunt in order to set the block size to 512 bytes per sector. 7 Setup Flowchart This flowchart shows the procedure for setting up the CRW2100S drive. For easy cross-referencing, the relevant pages in this manual are also given. STEP STEP 1 2 3 Do you have a SCSI card? YES NO 1-1 Purchase a SCSI card Recommended models: Adaptec AHA-2940-series (PCI) STEP Check that the SCSI card is STEP recognized correctly (P. 22, 30) up the CRW2100S drive Install the SCSI card Read this manual and insert the SCSI card into the appropriate PCI slot on the computer. 1-2 STEP Set 1. Fit the drive into the computer q Tower-type case (P. 15) As additional or replacement drive q Desktop-type case (P. 23) As a replacement drive STEP 4 5 6 Check that the CRW2100S drive is recognized correctly (P. 22, 30) STEP Install the CD writing software For details about how to install the software, refer to the documentation that came with it. STEP Start using the CRW2100S drive! Use the drive to create audio CDs, to back up data on your hard disk, or for whatever purpose suits your needs. 8 Setup Procedures Serial Number Once you have taken the CRW2100S drive out of its packaging, you should immediately note down the serial number found at the top of the drive with the bar code. You may need to refer to this number when requesting Customer Support services. One end of the audio cable has two connectors: a vertically-mounted type (PH) and a horizontally-mounted type (MPC). Choose one that matches your sound card's connector. The connector at other end of the cable is connected to "AUDIO OUT" of the CRW2100S drive. Make sure connector's lug is at the top. Lug AUDI O OU T RG L1 24 ID SE PARI LECT TY TERM BLOCIN ATOR K SIZE 1 SCSI INTE RF CONN ACE ECTO R DC IN PU T +5V G+ 12V Audio cable Horizontally-mounted type (MPC) Sound card Vertically-mounted type (PH) n You do not need to connect the audio cable to write audio CDs since the audio is passed over the SCSI bus. It is required to play back audio CDs on the CRW2100S drive via the computer's sound card. However, if a CD-ROM drive is already connected to the sound card, you should use this drive to play back your audio CDs. To listen to audio CDs without a computer sound card, connect headphones or speakers to the headphone jack on the CRW2100S drive's front panel. 19 Setup Procedures 8 Connect a 4-pin power cable to the power supply connector of the CRW2100S drive marked "DC INPUT. " AUDI O OU T RG L1 24 ID SE PARI LECT TY TERM BLOCIN ATOR K SIZ E 1 SCSI INTE RF CONN ACE ECTO R DC IN PU T +5V G+ 12V Top op 4-pin power cable Bottom n There may be more than one 4-pin power cable available. n These connectors are D-shaped so it is only possible to connect the power cables the correct way round. Do not apply excessive force when making this connection. 9 Tighten the four fastening screws on the side of the unit securely using a screwdriver. 20 Setup Procedures ) Attach the outer casing of the computer and any screws that were removed. !Reconnect the computer to the AC outlet and power it up. n When you power up the computer, make sure the LED on the panel of the CRW2100S drive blinks in green attempting reading disc information. 39) 21 Setup Procedures @ After the computer's operating system (Windows 95/98/98 Second Edition) has loaded, open the "Control Panel" and double-click on the "System" icon. [. . . ] 33 SCSI flat cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 26 SCSI ID number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Session-at-Once (SAO) . . . . . . . . . . . . . . . . . . . . . . . [. . . ]