User manual YAMAHA CRW2200SXZ

[. . . ] (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: Fax: Type of Equipment: Model Name: Yamaha Electronics Corporation, USA. 6660 Orangethorpe Avenue Buena Park, CA 90620 714-522-9105 714-670-0108 CD Recordable/Rewritable Drive CRW2200SX This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] Therefore, the CRW2200SX drive can actually be assigned an ID number from "0" to "6. " Set the SCSI ID numbers using the three dip switches as shown below. SCSI ID 0 SCSI ID 1 (Default) SCSI ID 2 SCSI ID 3 SCSI ID 4 SCSI ID 5 SCSI ID 6 SCSI ID 7 12 Setup Procedures Notes · The SCSI ID number for each device on the chain must be unique. Make sure the CRW2200SX drive's SCSI ID number is not the same as that of any other device on the chain. By factory default, the CRW2200SX drive is assigned ID number "1" but this can be changed. · When setting the dip switch, move the lever completely upward or downward. Termination Terminators prevent SCSI signals from being reflected off the last device in the chain. The SCSI terminator dip switch should be set to ON if the CRW2200SX drive is the last device on the SCSI chain. If the CRW2200SX drive is not the last device on the chain, the TERMINATOR dip switch should be set to OFF. Computer Hard disk drive (unterminated) CRW2200SX (terminated) SCSI card (terminated) Termination ON (Default) Termination OFF Set to ON if the CRW2200SX drive is the last device on the SCSI chain Set to OFF if the CRW2200SX drive is not the last device on the SCSI chain Note The default setting of the Terminator dip switch is ON. 13 Setup Procedures Connecting the CRW2200SX Drive 1 Shut down the computer and all the peripherals. 2 Make sure that the power switch on the rear panel of the CRW2200SX drive is set to STANDBY. 3 Connect the SCSI cable to either one of the SCSI card connectors on the rear panel of the CRW2200SX drive. Connect the other end of the SCSI cable to the SCSI card connector of the computer or the other SCSI device. SCSI card connector CRW2200SX rear panel SCSI connector SCSI cable 14 Setup Procedures About SCSI cable · The CRW2200SX drive requires a D-sub half-pitch 50-pin pin-type connector. The connector of the SCSI card may vary. You will need to purchase a SCSI cable with connectors suitable for both the drive and the SCSI card. The following are the most common types of SCSI connector: D-sub half-pitch 50-pin pin-type (as found on the CRW2200SX drive) Half-pitch 50-pin Centronics · The total of the length of SCSI cable you will need depends on the number of devices to connect. The number of devices to connect The total of the length of SCSI cables 1 to 3 devices 3. 0 m or less 4 to 7 devices 1. 5 m or less Note For stable operations, use the recommended length of SCSI cable. Example ­ when connecting 3 devices: Computer SCSI devices 1m 1m 1m The total of the length of SCSI cables is 3. 0 m. · When you use a SCSI cable, use with an Ultra SCSI mode compatible high impedance cable (characteristic impedance: 100 ± 10 ). 15 Setup Procedures Connecting the AC Adapter 1 Connect the included AC adapter to the DC-IN connector of the drive with the arrow on the adapter plug facing left, as shown below. DC-IN connector Screw Arrow 2 Connect the included power cable to the AC adapter (). Connect the other end of the power cable to the AC outlet (). Electrical plugs/sockets vary according to country/region. Notes · Operate the drive only with the included AC adapter. · The bottom of the drive and the AC adapter become warm during use. · Only by connecting the included AC adapter to a AC outlet, the electric power shown in the table below is consumed. Always unplug the AC adapter from the AC outlet when you do not intend to use the drive for a long time. AC adapter (model) SKB2505A SMB2505A Power source 100 V 120 V 220 ­ 240 V Power consumption 2. 1 W 2. 4 W 1. 4 W 16 Setup Procedures 3 Turn on the CRW2200SX drive first, then the computer. When the power of the CRW2200SX drive is turned on, the power LED on the front panel lights up in green. Power LED LED Note When you turn on the CRW2200SX drive, make sure the LED on the front panel blinks in green, which indicates that it is reading disc information. 31) Always turn on the devices in the SCSI chain before turning on the computer. This will ensure that they are recognized by the computer's operating system. [. . . ] 24 SCSI ID number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 30 Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Session-at-Once (SAO). . . . . . . . . . . . . . . . . . . . . . . . [. . . ]