User manual YAMAHA CRW3200UX

[. . . ] (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: Fax: Type of Equipment: Model Name: Yamaha Electronics Corporation, USA. 6660 Orangethorpe Avenue Buena Park, CA 90620 714-522-9105 714-670-0108 CD Recordable/Rewritable Drive CRW3200UX This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] For details about installing and using the CD writing software, refer to the documentation that comes with the CD writing software. 10 Preparing the CRW3200UX Drive Serial Number The serial number is printed on the label on the bottom of your CRW3200UX drive. When you have a question about the drive or need user support services, the serial number is required. Please write the serial number down in the space below. It may be difficult to check the serial number after setting up the drive or for any other reason. Serial number (10 characters: 3 letters + 7 numbers) Serial Number 11 Preparing the CRW3200UX Drive Note Place the CRW3200UX drive horizontally. 1 Connect the CRW3200UX Drive 1 2 Remove all USB devices connected to the computer, and turn on the computer. Be sure that the power switch on the rear panel of the CRW3200UX drive is turned off (STANDBY). 12 3 Connect the included USB cable to the CRW3200UX drive. The included USB cable has two types of plugs: Series A plug and Series B plug. Series A plug Series B plug Insert the Series B plug (with a quadratic section) of the included USB cable to the USB port of the CRW3200UX drive. USB cable (included) USB port Series B plug 4 Connect the included AC adapter to the DC-IN connector of the CRW3200UX drive. The arrow on the adapter plug faces to the screw (the left side of the connector). DC-IN connector Screw Arrow 13 Preparing the CRW3200UX Drive 5 Connect the included power cable to the AC adapter (). Connect the other end of the power cable to the wall socket (). Power cable (included) Note · Use the included AC adapter only. · The AC adapter may become warm during use under normal conditions. · The AC adapter consumes power, shown in the table below, while connected to the wall socket even if the power switch of the CRW3200UX drive is turned off. Remove the power cable from the wall socket when not using the CRW3200UX drive for a prolonged period. Power source 100 V, 120 V 220 V 230 V, 240 V Power consumption 0. 8 W 0. 9 W 1. 0 W 14 6 Turn on the power switch of the CRW3200UX drive. Blinks blue and then lights purple Note When turning on the CRW3200UX drive, be sure that LED on the front panel blinks blue and then lights purple. 3) 7 Connect the included USB cable to the computer. Connect the Series A plug (with a rectangular section) of the included USB cable to the USB port of the USB interface card. USB port USB cable (included) Series A plug Continued on next page 15 Preparing the CRW3200UX Drive Note · The CRW3200UX drive needs to be connected to the USB port on the computer. The drive connected to the computer via a USB hub may not operate properly. · When the CRW3200UX drive is connected to a USB 1. 1-compliant port on the computer, the drive operates with USB 1. 1 specifications. 9) 2 Install the Device Drivers Installation of the device drivers starts automatically when the CRW3200UX drive is connected to the computer. The device drivers need to be installed only once when first installing the device. For Windows 98 Second Edition Install the included device drivers. For details, refer to the separate manual "Device Driver Installation Guide" that comes with the CRW3200UX. For Windows Me/2000 Professional/XP The device drivers of the operating system standard are installed automatically. Note The device drivers are installed for each USB port. If you connect the drive to a USB port where the device drivers have not yet been installed, a message to install the device driver will be shown. 3 Check Recognition of the CRW3200UX Drive After connecting the CRW3200UX drive to the computer, follow the steps below to check that the drive is recognized properly by the computer. For Windows 98 Second Edition/Me 1 Select Start on the task bar, then Settings, Control Panel, System, and Device Manager tab. Note For Windows Me, if the System icon is not found in the Control Panel window, click view all Control Panel options on the left side of the window. 16 2 Check that the following icons are shown. a: "YAMAHA CRW3200E" in the "CDROM" item. [. . . ] This method enables you to add data into the same disc, one session at a time, as long as there is free space available on the disc. A disc that contains data written in several sessions by this method is defined as a multi-session disc, like a disc written by the Track-at-Once method. 35 Technical Notes Packet Writing This method is used to record data onto a disc on a file-by-file basis. This method divides a track into small segments called "packets" so that data can be written on a packet-by-packet basis, which means that you can write data in much the same way as you copy data to a floppy or hard drive. Since the data can be written easily, packet writing is proper to daily data backup. [. . . ]