User manual YAMAHA CRW8424EZ

[. . . ] CRW8424E SERIES OWNER'S MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DE INSTRUCCIONES CD-R/RW Drive COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Address: Telephone: FAX: Type of Equipment: Model Name: Yamaha Systems Technology, Inc. 100 Century Center Court San Jose, California 95112 (408) 467-2330 (408) 437-8791 CD Recordable/Rewritable Drive CRW8424E CRW8424E-NB This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. FCC INFORMATION (U. S. A. ) 1. [. . . ] Before removing the CD-ROM drive from the computer, make sure that all the cables have been removed from the CD-ROM drive's rear panel. Do not force pulling or apply excessive force to the CD-ROM drive. Replacing Drive 13 Installation 7 Set the CRW8424E as master. Plug the included plastic shunt to the MASTER jumper switch on the rear panel of the CRW8424E. Rear Panel AUDI O OUT RG L CSE L SLAV E MAST ER 1 IDE INTE CON RFACE NEC TOR DC IN PU T +5V G+ 12V RGL CSEL SLAVE MASTER Plastic shunt Set to MASTER. Jumper switches The plastic shunts actually contain metal for bridging the two pins of a jumper switch, creating an electrical connection between them when attached. When removed, the jumper switch is set to "OFF. " Store unused plastic shunts in a safe place where they will not be lost. Use a pair of long-nosed pliers to attach or detach the plastic shunts accordingly. However, make sure that the computer is switched off when doing so. 14 Installation 8 Slide the drive backwards into the slot. Do not apply excessive force when sliding the drive back into the drive bay slot. Additional Drive 8 Slide the CRW8424E drive backwards into the now-vacant bay without applying excessive force. Replacing Drive 15 Installation 9 Leave enough room behind the drive to connect the power, IDE and audio cables. Then tighten the four fastening screws on the sides of the unit by hand to hold the drive in place. Additional Drive 9 Leave enough room behind the drive to connect the power, IDE and audio cables. Then tighten the four fastening screws on the sides of the unit by hand to hold the drive in place. Replacing Drive 16 Installation ) Connect the IDE cable. Connect the included 40-pin IDE cable to the secondary IDE connector on the motherboard and to the IDE interface connector on the rear panel of the CRW8424E. Be sure to plug in the cable so that the colored line on the cable corresponds to pin #1 on the right end of the connector. Motherboard Magnified IDE connector section Secondary (connector) Primary (connector) Included IDE cable AUDIO OUT RG L CSEL SLAV E MAST ER 1 IDE INTER CONN FACE ECTO R DC +5 V INPUT G +1 2V 1 Colored line Included IDE cable · If an IDE cable has already been connected to the secondary IDE connector, replace it with the included IDE cable. · If you wish to continue using the IDE device you just removed, connect it to an available primary or secondary IDE connector. · When you connect two IDE devices to one IDE cable, be sure to assign them master or slave uniquely. To make the best use of the performance of the CRW8424E, Yamaha recommends you connect it as a sole secondary master. 17 Installation !Connect the audio cable between the CRW8424E drive and the computer's sound card, or the motherboard's audio connector if it has built-in audio. One end of the audio cable has two connectors: a vertically-mounted type (PH) and a horizontally-mounted type (MPC). Choose the one that matches your sound card's connector. The connector at other end of the cable is connected to "AUDIO OUT" on the CRW8424E drive. Make sure the connector's lug is at the top. Lug AUDI O OU T RG L CSEL SLAV MAS E TER 1 IDE INTE RF CONN ACE ECTO R DC IN PU T +5V G+ 12V Audio cable Horizontally-mounted type (MPC) Sound card Vertically-mounted type (PH) You do not need to connect the audio cable to write audio CDs since the audio is passed over the IDE bus. It is required to play¸ back audio CDs on the CRW8424E drive via the computer's sound card. However, if a CD-ROM drive is already connected to the sound card, you should use this drive to play back your audio CDs. To listen to audio CDs without a computer sound card, connect headphones or speakers to the headphone jack on the CRW8424E drive's front panel. 18 Installation @ Connect a 4-pin power cable to the power supply connector of the CRW8424E marked "DC INPUT. " AUDI O OU T RG L CSEL SLAV E MAST ER 1 IDE INTE RF CONN ACE ECTO R DC +5V INPU T G+ 12V Top 4-pin power cable Bottom There may be more than one 4-pin power cable available. These connectors are D-shaped so it is possible to connect the power cables in only the correct orientation. Do not apply excessive force when making this connection. 19 Installation # Tighten the four fastening screws on the side of the unit securely using a screwdriver. Additional Drive # Tighten the four fastening screws on the side of the unit securely using a screwdriver. Replacing Drive 20 Installation $ Attach the outer casing of the computer and any screws that were removed. Additional Drive $ Attach the outer casing of the computer and any screws that were removed. Replacing Drive 21 Installation % Reconnect the computer to the AC outlet and power it up. Additional Drive When you power up the computer, make sure both LEDs on the panel of the CRW8424E light up together for brief moment. % Reconnect the computer to the AC outlet and power it up. Replacing Drive When you power up the computer, make sure both LEDs on the panel of the CRW8424E light up together for brief moment. 22 Installation ^ When using Windows 95/98/98SE, after the computer's operating system has loaded, open the "Control Panel" and double-click on the "System" icon. Select the "Device Manager" tab and double-click on "CD-ROM". If the drive has been correctly installed, it should be listed as shown in the figure on the right. When using Windows NT, you can verify by opening the "Control Panel", double-clicking on "SCSI Adapter" and clicking the "Devices" tab. For more information on using the operating system, refer to the documentation that came with the operating system. * This is a screen shown in the Windows 98 environment. If there is an or mark etc. [. . . ] 23 F firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 11 H headphone jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 headphone volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]