User manual YAMAHA CS-5

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] All other switches should remain in their "up" positions. 6. Make NOTE the required daisy chain connections between the MY16-ES64 card and the CS-5 units. · When setting up a ring type network, initial settings should be made with the system connected as a daisy chain. Close the ring connection after the initial settings have been made. Quick Setup 7. Connect the computer to the MY16-ES64 EtherSound [IN] connector. 5. Select the control source determined in the previous section via the Quick Setup Head Amp Controller field. 8. If you selected option B in step 1, connect the digital mixing console's [REMOTE] connector to the MY16-ES64 card [HA REMOTE] connector via a 9-pin D-sub cross cable. 9. Select the word clock master on the digital mixing console. For a daisy chain network select either [INT48K] or [INT44. 1K], and for a ring network select the [1/2] channel of the slot in which the MY16-ES64 card is installed. 6. Select the EtherSound network connection type via the Network Mode field. 11. If you selected option A in step 1, and are using an LS9-32 console, select [SLOT 1] via the console's EXTERNAL HA display COMM PORT parameter. 14 CS-5 Owner's Manual Setup 7. If a ring network is to be used, use the Channel Allocation slider to select an input/output channel combination. For daisy chain configurations, if the CS-5 is the primary master, turn this checkbox OFF to select the CS-5 internal word clock or ON to use the EtherSound module word clock. If the CS-5 is not primary master, the Emergency Clock checkbox has no effect. NOTE Select [Unicast] when controlling the head amplifiers from a compatible digital mixing console, and select the MY16ES64 card as the communication target. It is also necessary to set the MY16-ES64 Serial Communication Mode. Select [Slave] when controlling the head amplifiers directly from the AVS-ESMonitor application. The [Multicast] setting is provided for future expansion, and is not currently available. Head Amp Remote Option · See page 13 for information on the Quick Setup function. Settings from DIP Switch 5­8 (for M7CL-48ES) When controlling the head amplifiers from the AVS-ESMonitor application, a Head Amp page that provides access to the head amplifier control parameters will be added to the These are the settings for use when connecting with the M7CL-48ES using the Auto Configure function. The settings of "Network Mode" and "Unicast Tunneling to" are displayed by scanning the status of the DIP switches 5­8 when the power is turned ON. When you want to temporarily change the EtherSound settings (including "Network Mode" and "Unicast Tunneling to") in the AVS-ESMonitor application, turn the Auto Configure checkbox OFF. 16 CS-5 Owner's Manual Setup Setup Error Messages If any of the error messages listed below appears while executing the Quick Setup function, resolve the problem as required and then execute Quick Setup again. When changing a Setup ID setting be sure to turn the device's power OFF, change the DIP switch settings as required, and then turn the device ON again. Error Message Setup ID is discontinuous. Setup ID #n not found. Details and Solution The Setup ID numbers are not sequential--ID "#n" is missing. Referring to the "Preparation" instructions on page 13, use the DIP switches to set the Setup ID numbers in sequence beginning from #1. Two or more CS-5 units have the same Setup ID number. [. . . ] · For the removal of the battery at the moment of the disposal at the end of life please consult your retailer or Yamaha representative office in your country. · Gooi de batterij niet weg, maar lever hem in als KCA. Instead, hand it in as small chemical waste. (lithium disposal) 174 CS-5 Owner's Manual For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. [. . . ]