User manual YAMAHA CT-410

[. . . ] 2 Retain Instructions ­ The safety and operating instructions should be retained for future reference. 3 Heed Warnings ­ All warnings on the unit and in the operating instructions should be adhered to. 4 Follow Instructions ­ All operating and other instructions should be followed. 5 Water and Moisture ­ The unit should not be used near water ­ for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. [. . . ] MAIN Select this if you do not use a subwoofer. The LFE signals are directed to the main speakers. BOTH Select this if you use a subwoofer and you want to mix the main channel low-frequency signals with the LFE signals. dB dB 3 I/O ASSIGN It is possible to assign jacks according to the component to be used if this unit's DIGITAL jack settings (component names for terminals) differ from that component. This makes it possible to change the jack assignment and effectively connect more component. Once you assign, you can select that component with INPUT l / h (or the input selector buttons). Notes · When playing a 2-channel source (CD, MD, tape, video cassette etc. ), select BOTH position to direct low bass signals (below 90 Hz) to the SUBWOOFER jack. · When you select SMALL (SML) for items "CENTER SP", "MAIN SP" and "REAR LR SP", the low-frequency signals (90 Hz and below) from those channels are added to the LFE and output to the subwoofer. HTR-5450 I 3A (1) (for the OPTICAL OUTPUT jack) Initial setting: (1) MD/CD-R I MAIN LVL (main level mode) Change this setting if you cannot match the output level of the center and rear speakers with the main speakers because of the unusually high-efficiency performance of the main speakers. Choices: NORM (normal), ­10 dB Initial setting: NORM I 3B (2) to (4) (for the OPTICAL INPUT jacks) Initial settings: (2) MD/CD-R (3) DVD (4) D-TV/CBL NORM (normal) Normally select this setting. ­10 dB Select this if you cannot match the output level of your effect speakers with that of your main speakers when using the test tone. This setting decreases the main speaker output level to about one-third of the normal level. 34 SET MENU I 3C (5) (for the COAXIAL INPUT jack) Initial setting: (5) CD 5 DOLBY D. SET (Dolby Digital set) This setting is effective only when this unit decodes Dolby Digital signals. INTRODUCTION I LFE LEVEL Note · You cannot select an item more than once for the same type of jack. Use this feature to adjust the output level of the LFE (lowfrequency effect) channel when playing back a Dolby Digital signal. The LFE signal carries the low-frequency special effect sound which is only added to certain scenes. The delay time can be individually adjusted to all DSP programs. Notes · If "CENTER SP" in the SET MENU is set to the NON position, the sound output level of the center speaker cannot be adjusted. This is because the center channel sound is automatically output from the right and left main speakers. · Once the sound output level has been adjusted, the level will be the same for all DSP programs. Speaker Center Right rear Left rear Subwoofer Preset value (dB) 0 0 0 0 PREPARATION Notes · Adding too much delay will cause an unnatural effect with some sources. · The sound is momentarily interrupted while adjusting the delay time. Program CONCERT HALL JAZZ CLUB ROCK CONCERT DISCO 5CH STEREO GAME TV SPORTS MONO MOVIE 70 mm SPECTACLE DGTL SPECTACLE DTS SPECTACLE 70 mm SCI-FI DGTL SCI-FI DTS SCI-FI 70 mm ADVENTURE DGTL ADVENTURE DTS ADVENTURE 70 mm GENERAL DGTL GENERAL DTS GENERAL PRO LOGIC/NORMAL DOLBY DIGITAL/NORMAL DTS DIGITAL SUR. /NORMAL PRO LOGIC/ENHANCED DOLBY DIGITAL/ENHANCED DTS DIGITAL SUR. /ENHANCED Preset value (ms) 45 30 15 26 2 36 10 69 23 13 13 20 16 16 20 15 15 20 15 15 20 5 5 20 5 5 1. 7. ADVANCED OPERATION 8. 9. APPENDIX English 37 DELAY TIME AND SPEAKER OUTPUT LEVELS Adjusting Method Adjustments should be performed with the remote control while watching the information on the display. 3 Press ­ or + to adjust the delay time or speaker output levels. 4 1 Repeat steps 2 and 3 to adjust the settings of any other item. Notes 3 2 · If "CENTER SP" or "REAR LR SP" is set to NON, or "BASS OUT" is set to MAIN, the output level of that speaker cannot be adjusted. · When you adjust the output level with TIME/LEVEL, the settings you made with the test tone will be changed. · To adjust speakers other than the subwoofer, the adjusting procedure using test tones on page 19 is recommended. 1 Press AMP(TUNER) on the component selector. 2 Press TIME/LEVEL repeatedly to select the item you want to adjust. Each time you press TIME/LEVEL, the selected item changes and appears on the display as below. Memory back-up The memory back-up circuit prevents the stored data from being lost when this unit is set in the standby mode. If, however, the power cord is disconnected from the AC power outlet or the power is cut for more than one week, the latest values for the delay time and the center/rear/ subwoofer output levels that were set will automatically return to the preset values. [. . . ] 12 F Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 H HP TONE CTRL (SET MENU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 T TAPE/MD mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Test tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]