User manual YAMAHA CVP-605

[. . . ] The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement. Warning: Do not attempt to recharge, disassemble, or CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. incinerate this type of battery. Dispose of used batteries promptly and as regulated by applicable laws. [. . . ] (This is available only when recording the melody. ) For information on gate time settings, see below. Each press of this button toggles among the three basic note selectors at the bottom of the display: normal, dotted, and triplet. (This is available only when recording the melody. ) Deletes the event at the cursor. Use these to move the selected event, in units of measures (BAR), beat, and clocks. For information on measure/beat/clock settings, see below. Specifies the type of note to be input next. (Sixteenth notes are available only when recording the melody. ) This also determines the position to which the pointer will advance after a note has been entered. END To close the STEP RECORD display, press the [EXIT] button. Make sure to store the recorded data by pressing the [I] (SAVE) button (page 45). I Measure/Beat/Clock Measure 1 Beat Clock 1 2 3 4 000- 000- 000- 0001919 1919 1919 1919 2 1 2 3 4 000- 000- 000- 0001919 1919 1919 1919 I Velocity The table below shows the available settings and the corresponding velocity values. Kbd. Vel Actual playing strength fff 127 ff 111 f 95 mf 79 mp 63 p 47 pp 31 ppp 15 I Gate Time The following settings are available: Normal . . . . . . . . . . . . . . . . . . . . . . . The gate time (note length) can be specified as a percentage by using the [DATA ENTRY] dial. 98 CVP-205/203 Recording Your Performances and Creating Songs-- Song Creator Recording Melodies -- Step Record (Note) In this section, we'll show you how to use Step Recording by guiding you through this actual music example, shown at right. The operations here apply to step 6 on page 98. 1 1-1 1-2 While holding down this note. . . Select this note. 1-3 . . . press this (to input a tie). The notation display on the instrument (CVP-205) may not be accurate, especially for tied notes or longer notes. To have the notation displayed accurately, set the gate time to tenuto by using the [H] button, and input the notes as desired. 2 2-2 2-3 2-4 2-1 Select this note. 3 3-1 Press this button to display the dotted notes. 3-3 3-2 Select this note. 4 4-1 4-3 Call up the normal notes by pressing this button. 4-2 Select this note. To input rests, simply move the measure/beat/clock location for the desired rest time, then input the next note. I Play back the newly created melody Use the [C] ( L ) button to move the cursor to the beginning of the song, and press the SONG [START/STOP] button to hear the newly entered notes. To actually enter the recorded data, press the [EXIT] button. When the Pedal Punch In/ Out function is set to ON, the current function assignment of the sostenuto pedal is cancelled. Punch Out This maintains all data following the point at which recording is stopped. Punch Out At Overwrite recording continues until the indicated Punch Out measure (set by the [6LM] buttons), then stops at that Punch Out measure, after which song playback continues normally. About Punch In/Out This feature is useful primarily for re-recording or replacing a specific section of an already recorded channel. The illustrations below indicate a variety of situations in which selected measures in an eight-measure phrase are re-recorded. REC START setting REC END setting NORMAL REPLACE ALL NORMAL PUNCH OUT NORMAL PUNCH OUT AT=006 FIRST KEY ON REPLACE ALL FIRST KEY ON PUNCH OUT FIRST KEY ON PUNCH OUT AT=006 PUNCH IN AT=003 REPLACE ALL PUNCH IN AT=003 PUNCH OUT PUNCH IN AT=003 PUNCH OUT AT=006 Original data 1 Start/start overwrite recording *1 2 3 4 5 6 7 8 Stop recording *2 *1 When measures 1 - 2 are not overwritten, recording starts from measure 3. *2 You'll have to press the [REC] button at the end of 5 measures. 1 Start/start overwrite recording *1 2 3 4 5 Stop recording *2 Deleted 1 Start/start overwrite recording *1 2 3 4 5 6 7 8 Stop overwrite recording/ play original data 1 Start/ play back original data 2 3 4 5 6 7 8 Start playing the keys/ start overwrite recording Stop recording *2 1 Start/ play back original data 2 3 4 5 Stop recording *2 Deleted Start playing the keys/ start overwrite recording 1 Start/ play back original data 2 3 4 5 6 7 8 Start playing the keys/ start overwrite recording Stop overwrite recording/ play original data 1 Start/ play back original data 2 3 4 5 6 7 8 Start overwrite recording Stop recording *2 1 Start/ play back original data 2 3 4 5 Stop recording *2 Deleted Start overwrite recording 1 Start/ play back original data 2 3 4 5 6 7 8 Previously recorded data Newly recorded data Deleted data Start overwrite recording Stop overwrite recording/ play original data 1 2 3 4 5 7 102 CVP-205/203 Recording Your Performances and Creating Songs-- Song Creator Editing a Recorded Song Whether you've recorded a song using Quick Recording, Multi Recording, or Step Recording, you can use the editing features to change the song data. Editing Channel-related Parameters -- Channel Calling up the operations here apply to step 4 on page 97. To call up the display shown below, use the [BACK]/[NEXT] buttons. Quantize Quantize lets you "clean up" or tighten the timing of a previously recorded channel. For example, the following musical passage has been written with exact quarter-note and eighth-note values. Even though you think you may have recorded the passage accurately, your actual performance may be slightly ahead of or behind the beat. Quantize allows you to align all the notes in a channel so that the timing is absolutely accurate to the specified note value (see below). Use this to select the desired edit operation. Calls up the SONG display, from which you can save the edited data. Determines how strongly the notes will be quantized. If a value less than 100% is selected, notes will be moved toward the specified quantization beats only by the specified amount. Applying less than 100% quantization lets you preserve some of the "human" feel in the recording. Executes the Quantize operation. After the operation is completed, this button changes to [UNDO], letting you restore the original data if you're not satisfied with the Quantize results. [. . . ] De C. V. , Departamento de ventas Javier Rojo Gomez No. 1149, Col. Tel: 686-00-33 KOREA Yamaha Music Korea Ltd. 16F 23-8 Yoido-dong, Youngdungpo-ku, Seoul, Korea Tel: 02-3770-0661 GREECE Philippe Nakas S. A. Navarinou Street 13, P. Code 10680, Athens, Greece Tel: 01-364-7111 MALAYSIA Yamaha Music Malaysia, Sdn. , Bhd. [. . . ]