User manual YAMAHA D-65

[. . . ] Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc. ) or high humidity (bathroom, outside on a rainy day, etc. ). Doing so may result in deformation, discoloration, damage or deterioration. When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. [. . . ] Tighten the knob loosened and fix the position of pipe . FP6110A (Foot Pedal) (1) Checking the contents of RS40 Open the RS40 (Rack System) package and confirm the contents. Figure 2: RS40 (Rack System) RS40 (1) Fastening Screw (2) *1 * In the following steps, loosen the knobs first, decide the position of the pipe, and then tighten the knobs. Be careful not to tighten the knobs excessively. For better performance, make minor adjustments for each part of the unit with the knobs after the assembly is completed. Drum Key (1) 6 7 8 q w e r t y u i DTXPL (Drum Trigger Module) TP65 (Drum Pad) AC Adaptor HH65 (Hi-Hat Controller) PCY65 (Single-zone Cymbal Pad) RS40 (Rack System) KP65 (Kick Pad) FP6110A (Foot Pedal) Cable Band (10) *2 9 Assembly Manual (1) *3 - RS40 Loosen the two knobs (e) aligned at the base of pipe , and move pipe slightly outward in a counterclockwise direction. Tighten the two knobs loosened and fix the position of pipe . Loosen the two knobs ((f) on the middle left) aligned at the base of pipe . Move pipe slightly outward in a clockwise direction. Tighten the two knobs loosened and fix the position of pipe . Loosen the two knobs ((g) on the upper left) aligned at the base of pipe , and move pipe outward in a clockwise direction until it is about 45 degrees from pipe . Tighten the two knobs loosened and fix the position of pipe . Check that the entire rack system is stable. Tighten the knobs loosened and fix the positions of the cymbal holders. Loosen the two knobs (h) aligned along the pipe with the Trigger Module attachment part . Adjust the Trigger Module attachment part so the operating panel will face upward diagonally to your side when set. Hold the Trigger Module attachment part firmly and turn it gradually. Tighten the two knobs loosened and fix the position of the Trigger Module attachment part . * YAMAHA logo printed on pipe is facing the opposite side. Continued on the next page (on the back side) Mounting the pads and the trigger module on the rack system Mount the pads and the trigger module on the rack system. Then position the kick pad and the hi-hat. 2 Attach the PCY65 (Cymbal pad) (@4) to the cymbal holder (@1) as shown in Figure 14. Attach the felt washer (@3) and the wing nut (@2) removed in step 1, and tighten it. Turn the wing nut until you are certain that the cymbal pad is attached. The cymbal pad is designed to shake when you hit the surface, even when the wing nut is tightened securely. Attaching the FP6110A (Foot pedal) to KP65 (Kick pad) Figure 21: FP6110A and KP65 Figure 22: T-handlet bolt Figure 28: Diagram of standard connection Mounting the DTXPL (Trigger module) Figure 15: Pads Assembly-4 Figure 16: Module stand-1 Mounting the TP65 (Drum pads) on the rack system Figure 8: Pads Assembly-1 Figure 9: TP65 %1 FP6110A (Foot pedal) %2 KP65 (Kick pad) %3 T-handlet bolt @5 Module stand @6 Clamp !1 Clamp bolt !2 TP65 (Rear side) 1 Turn the T-handlet bolt (%3) of the foot pedal (%1) in a counterclockwise direction and loosen it. Figure 23: Attaching FP6110A Figure 24: Adjustment 1 1 See Figure 16. Loosen the knob of the clamp (@6) (shown with stand (@5) from the clamp (@6). ) and remove the module See Figure 9. Attach the clamp bolts (!1) on TP65s (!2). [. . . ] Place the HH65 (Hi-hat controller) (^2) under the TP65 (Hi-hat cymbal) (^1). Place the KP65 (Kick pad) with FP6110A (Foot pedal) (^3) at the bottom center of the RS40 (rack system). Figure 19: KP65 Assembly 3 4 5 6 ^1 TP65 (Hi-hat cymbal) ^2 HH65 (Hi-hat controller) ^3 KP65 (Kick pad)+ FP6110A (Foot pedal) &1 Power supply jack (DC IN 12V) &2 Cable clip &3 Power switch 1 Make sure to turn the power off (the Standby/ On switch (&3) is set to the standby position). Attach the TP65 (Drum pad) to the tom holder as shown in Figure 11. Tighten the clamp bolt and attach the drum pad TP65 firmly. Loosen the knob (shown with ) of the tom holder on the upper left. [. . . ]