User manual YAMAHA D24

[. . . ] DIGITAL MULTITRACK RECORDER Owner's Manual TIME DISPLAY CAPTURE ABS/REL REMAIN OVER ­dB 0 2 6 10 12 14 20 18 30 20 42 26 60 DIGITAL MULTITRACK RECORDER POWER OVER 0 ­dB 2 6 12 20 30 42 60 ABS 00 00 00 00 YAMAHA D24 WC INT BIT FS 48K TC MASTER H M S F VARI SPEED UTILITY SETUP LOCK READY READY 24 V. TRACK SELECT EDIT UNDO/ REDO ON OFF L R PROJECT SEARCH 1 RECORD READY 2 3 4 5 6 7 8 7 8 9 PROJECT SELECT JOG ON LAST REC OUT IN SET AUTO PUNCH 4 SOLO/ SELECT 5 6 LOC MEM RECALL RTN TO ZERO ROLL BACK A B REPEAT A B REHE 0 10 PHONES LEVEL REC 1 PEAK HOLD AUTO INPUT ALL INPUT FORMAT CHASE 2 3 LOC MEM STORE REW FF STOP PLAY 0/MONITOR SELECT CANCEL ENTER LOCATE PHONES JOG/DATA SHUTTLE/ CURSOR Keep This Manual For Future Reference. E FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. [. . . ] To delete another part, press the [ENTER] button to return to step 4. 13 Press the [EDIT] button to leave edit. The EDIT indicator goes out. In the following example, the part between the ST and ED points on track 2 is deleted and subsequent material is moved forward. ST point 00:01:00. 00 ED point 00:01:15. 00 TR 2: Before Part to be deleted Subsequent material moved forward TR 2: After When a part is deleted, although it can no longer be accessed, its sound files remain on disk as unused files, taking up disk space, and reducing the time remaining for additional recording. To delete these unused files and recover the disk space, use the Optimize function. See "Recovering Disk Space" on page 172 for more information. D24--Owner's Manual 104 Chapter 10--Editing Parts Erasing Parts The Part Erase function is used to erase part of a track. The following points, which can be adjusted in sub-frame steps, can be selected when specifying edit points: LAST REC IN, LAST REC OUT, A, B, or a locate memory from 1 through 99. Note that you must set these points before entering the Part Erase function. See the Quick Locate Chapter on page 57 for more information about setting these points. 1 Press the [EDIT] button. Use the JOG/DATA dial to select "PART EDIT, " and then press the [ENTER] button. Use the JOG/DATA dial to select "ERASE, " and then press the [ENTER] button. "PART ERASE--TR nn" appears on the display ("nn" being the number of the track from which the part is to be erased). 2 3 4 Use the JOG/DATA dial to select the track. You can select individual tracks, track pairs, or all tracks: 1­8, 1/2­7/8, or ALL. To erase part of a virtual track, assign it to a main track first, and then erase. 5 Press the [ENTER] button. "ERS TR nn--ST MARK IN" appears on the display ("nn" being the number of the selected track and "ST" being the start point of the part to be erased). 6 7 Use the JOG/DATA dial to select one of the following points: MARK IN, MARK OUT, MARK A, MARK B, or a locate memory from 1 through 99. "ERS TR nn--ST 00:00:00. 00. 0" appears on the display ("00:00:00. 00. 0" being the position of the selected point). 8 Use the JOG/DATA dial or keypad to adjust the start position, and then press the [ENTER] button. "ERS TR nn--ED MARK IN" appears on the display ("ED" being the end point of the part to be erased). 9 Use the JOG/DATA dial to select one of the following points: MARK IN, MARK OUT, MARK A, MARK B, or a locate memory from 1 through 99. If the duration of the specified part is less than 15 milliseconds, the minimum size, the message "TOO SHORT" appears. "ERS TR nn--ED 00:00:00. 00. 0" appears on the display ("00:00:00. 00. 0" being the position of the selected point). 10 Press the [ENTER] button. 11 Use the JOG/DATA dial or keypad to adjust the end position, and then press the [ENTER] button. "EDIT ERASE--ARE YOU SURE" appears on the display. D24--Owner's Manual Erasing Parts 105 12 Press the [ENTER] button to erase the specified part, or the [CANCEL] button to cancel. When the erase operation is complete, "FINISHED" appears on the display and the UNDO/REDO indicator lights up, indicating that it can be undone. See "Undoing a Recording or Edit" on page 35 for more information. To erase another part, press the [ENTER] button to return to step 4. 13 Press the [EDIT] button to leave edit. The EDIT indicator goes out. In the following example, the part between the ST and ED points on track 2 is erased. ST point 00:01:00. 00 ED point 00:01:15. 00 TR 2: Before Part erased TR 2: After When a part is erased, although it can no longer be accessed, its sound files remain on disk as unused files, taking up disk space, and reducing the time remaining for additional recording. [. . . ] If the source is copy protected, however, it's possible to make a first-generation copy, but further copies cannot be made from the first-generation copy. SCMS is only effective when copying via digital connections. Recordings made via analog connections are not affected. SCSI (Small Computer Systems Interface)--Pronounced "scuzzy. " A parallel interface for connecting computers and peripherals, such as hard disk drives, removable disk drives, and scanners. [. . . ]