User manual YAMAHA D24V2

[. . . ] Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. [. . . ] You can select individual tracks, track pairs, or all tracks: 1­8, 1/2­7/8, or ALL. To delete part of a virtual track, assign it to a main track first, and then delete. 5 Press the [ENTER] button. "DEL TR nn--ST MARK IN" appears on the display ("nn" being the number of the selected track and "ST" being the start point of the part to be deleted). 6 7 Use the JOG/DATA dial to select one of the following points: MARK IN, MARK OUT, MARK A, MARK B, or a locate memory from 1 through 99. "DEL TR nn--ST 00:00:00. 00. 0" appears on the display ("00:00:00. 00. 0" being the position of the selected point). 8 Use the JOG/DATA dial or keypad to adjust the start position, and then press the [ENTER] button. "DEL TR nn--ED MARK IN" appears on the display ("ED" being the end point of the part to be deleted). 9 Use the JOG/DATA dial to select one of the following points: MARK IN, MARK OUT, MARK A, MARK B, or a locate memory from 1 through 99. If the duration of the specified part is less than 15 milliseconds, the minimum size, the message "TOO SHORT" appears. "DEL TR nn--ED 00:00:00. 00. 0" appears on the display ("00:00:00. 00. 0" being the position of the selected point). 10 Press the [ENTER] button. 11 Use the JOG/DATA dial or keypad to adjust the end position, and then press the [ENTER] button. "EDIT DELETE--ARE YOU SURE" appears on the display. D24V2V2--Owner's Manual Deleting Parts 103 12 Press the [ENTER] button to delete the specified part, or the [CANCEL] button to cancel. The part is deleted and subsequent material is moved forward. When the delete operation is complete, "FINISHED" appears on the display and the UNDO/REDO indicator lights up, indicating that it can be undone. See "Undoing a Recording or Edit" on page 35 for more information. To delete these unused files and recover the disk space, use the Optimize function. See "Recovering Disk Space" on page 172 for more information. D24V2V2--Owner's Manual 106 Chapter 10--Editing Parts Inserting Parts The Part Insert Space function is used to insert an empty part into a track. Existing material on the track is moved backward. The following points, which can be adjusted in sub-frame steps, can be selected when specifying edit points: LAST REC IN, LAST REC OUT, A, B, or a locate memory from 1 through 99. Note that you must set these points before entering the Part Insert Space function. See the Quick Locate Chapter on page 57 for more information about setting these points. 1 Press the [EDIT] button. Use the JOG/DATA dial to select "PART EDIT, " and then press the [ENTER] button. Use the JOG/DATA dial to select "INSERT SPACE, " and then press the [ENTER] button. "PART INSR S--FROM TR nn" appears on the display ("nn" being the number of the track into which the empty part is to be inserted). 2 3 4 Use the JOG/DATA dial to select the track. You can select individual tracks, track pairs, or all tracks: 1­8, 1/2­7/8, or ALL. To insert an empty part into a virtual track, assign it to a main track first, and then insert. 5 Press the [ENTER] button. [. . . ] Sampling rate -- The number of times per second an analog audio signal is sampled (i. e. , measured) during A/D conversion. SCMS (Serial Copy Management System)--Pronounced "scums, " a protection system intended to prevent illegal copying of music. SCMS allows one-time serial copying of copy-protected material. If the source is not copy protected, it's possible to make any number of digital-to-digital copies of the material. [. . . ]