User manual YAMAHA DIGITAL MIXING STUDIO 01X

[. . . ] SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. WARNING: Do not place this product in a position where anyone could walk on, trip over , or roll anything over power or connecting cords of any kind. The use of an extension cord is not recommended! [. . . ] From the pop-up menu, select the desired Category. For details on the available Categories and Commands, refer to the Cubase SX documentation. Using the Function buttons The eight Function buttons [F1] - [F8] provide a powerful and versatile way to customize DAW control and streamline your recording, editing and mixing work. Just as with the Key Commands, these buttons can be assigned to any desired function, operation or command. Used in conjunction with the [SHIFT] button, you can program up to thirteen different key commands for instant, one-touch control from the 01X. What's more, the two FOOT SWITCH jacks can also be assigned, letting you control two separate functions with connected footswitches. Assigning the Function buttons 4 Next, click the Command cell for the button, and select the desired Command from the pop-up menu. 1 From the Devices menu, select "Device Setup. . . " 2 Select "Mackie Control" from the list. 5 Repeat steps 3 and 4 above to program the other Function buttons and their [SHIFT] combinations. Also, program the footswitches if desired (User A and B correspond to FOOT SWITCH jacks A and B, respectively. ) · The [SHIFT] combinations with [F1], [F2] and [F4] are reserved for other functions (TRACK, MIXER and CLOSE), and cannot be programmed. 6 Click [Apply] to enter the settings, then click [OK]. 82 01X Owner's Manual Recording/Playback/Remote Control Undo The [UNDO] button performs the same function as Undo in the sequencer -- allowing you to cancel the last edit made and restore the previous condition of the song. Simply hold down the [SHIFT] button and press [UNDO]. The last edit you made will be repeated, cancelling the just-made Undo. Before Using 01X Owner's Manual Saving your song You can also conveniently save your song from the 01X panel, by simply pressing the [SAVE] button. · For more information on the Remote Functions, refer to the Remote Function List (page 104). 83 Appendix Reference Getting Started Basics Section Reference Function Tree/Function List This chart shows the names, ranges and explanations of all settable parameters in the Internal mode, listed in order according to the function tree. These parameters can be set not only from the 01X itself, but also conveniently from a computer--using the included software program "Studio Manager" (see separate Installation Guide and PDF documentation). · · · · Operation procedures for calling up each parameter display are indicated in the chart ([button] [button]). For information on the Display Indication and mode selection, see pages 37, 38. For information on the Remote mode, see page 104. For information on the "Home" operation, see page 37. To restore the default value of the selected parameter, simultaneously hold down the [SHIFT] button and press the appropriate channel knob ([1] ­ [8]). Before Using Basics Section Getting Started Reference Appendix · Never attempt to turn off the power while data is being written to Flash ROM (while an "EXECUTING BACKUP. PLEASE KEEP POWER ON. . . " message is shown). Turning the power off in this state results in loss of all user data and may cause the system to freeze (due to corruption of data in the Flash ROM). Chart Indications The example below shows and describes the various indications in the Reference chart. * These indications are for example purposes only, and differ from the actual chart. Knob Function name/ settings Explanation Prompt Related pages Block diagram SCENE MODE [SCENE] DISPLAY [ (or [SCENE] [SCENE] [SCENE]) 1 SCENE LIBRARY / ] [PAGE SHIFT] + DISPLAY [ / ] q 00 ­ 99 (Library number) Determines the Library number. Preset Scene numbers and write-protected Scenes are indicated by asterisks (*) in the display and cannot be changed. Library number 00 is read-only and contains the default settings for all parameters. By using Recall (below) to call up this Scene, you can restore all 01X settings to their initial default state. This Scene can also be called up via an external MIDI device by sending an appropriate program change message (according to the setting in Program Change Assign Table; see page 94). When Q is set to HPF, this turns the filter on or off. Pressing the [EQ LOW] and [EQ HIGH] buttons simultaneously resets all band parameters (gain, frequency and Q) for the selected channel. No 36 65 q q­i (y) -18. 0dB ­ +18. 0dB Yes w A B C D E F A: These pages can be selected by using the DISPLAY [ / ] buttons. [. . . ] 4, Jakarta 12930, Indonesia Tel: 21-520-2577 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México S. A. 09300, México, D. F. , México Tel: 55-5804-0600 SPAIN/PORTUGAL Yamaha-Hazen Música, S. A. 17, 200, 28230 Las Rozas (Madrid), Spain Tel: 91-639-8888 KOREA Yamaha Music Korea Ltd. 16F 23-8 Yoido-dong, Youngdungpo-ku, Seoul, Korea Tel: 02-3770-0660 BRAZIL Yamaha Musical do Brasil Ltda. [. . . ]