User manual YAMAHA DMC1000 V3.0

[. . . ] IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. [. . . ] Note: If the punch-in channels already contain the parameter events selected in the OVERWRITE section, punching-in immediately overwrites the existing events. Be careful while selecting parameters in the OVERWRITE section so that you will not delete events you wish to retain. 6 Adjust the controls of the selected channels. 7 To punch out the channels, press the corresponding [SEL] buttons again. A confirmation window regarding updating the Automix data appears. Tip: You can also select the recording channels first using the [SEL] buttons, start the timecode source, then select the desired parameters in the OVERWRITE section to punch in and out. Punching In & Out Individual Events Even if you selected some parameters in the OVERWRITE section, you can punch in an individual parameter by following the steps below: 1 In the OVERWRITE section, select the parameters you want to record. 2 Move the cursor to the REC or AUTO REC button at the bottom of the page, then press [ENTER]. 3 Press the [AUTO] button on the top panel. Make sure that the [SEL] button indicators for all channels are lit green. The REC and PLAY buttons are highlighted and event recording is armed. However, no events are yet recorded since no channels are selected. DMC1000 V3. 0--Owner's Manual Punching In & Out 189 5 Perform the following operations to punch in and out individual events. Parameters Channel Input Channel Levels (faders) Bus Out, Aux Send Stereo Out Pan Input PAN FADER OVERWRITE Operation Set Layer to Iinput, Fader mode to Fader Set Layer to Master, Fader mode to fader Stereo Out fader Set Layer to Input, Encoder mode to Pan Select Input Layer and assign Surround LFE Level or Surround Pan Wheel to the Encoders Use SELECTED CHANNEL EQUALIZER section. Recorded events of the currently-selected channel are reflected in the SELECTED CHANNEL section controls and displays. Note: If the current effects type is different from that used when the effects parameter edits were recorded, the parameter edits will not be played back. When you rerecord effects parameter edits from the beginning, it is recommended that you delete the existing effects events offline. DMC1000 V3. 0--Owner's Manual Automix Main Page 191 Automix Main Page This section explains the Automix Main page. This page enables you to set the basic Automix parameters and record and play back Automixes. To locate the Automix | Main page, press the DISPLAY ACCESS [AUTOMIX] button repeatedly until the page appears. 1 4 6 7 J 2 3 5 8 9 K L M N A FREE O P Q R The amount of free Automix memory remaining is displayed here in kilobytes, as a percentage, and by a bar graph. B SIZE The size of the current Automix and the size of any Automix data in the undo buffer are displayed here in kilobytes. C TIME REFERENCE The timecode source and frame rate specified on the Time Ref page (see page 182) are also displayed here. D INT START TIME This parameter sets the start time of the DMC1000 V3. 0 internal timecode generator in hours, minutes, seconds, frames, and subframes. Move the cursor to a digit you wish to change, and rotate the Parameter wheel or press the [INC]/[DEC] buttons to modify the value. Press the [ENTER] button to reset the currently-selected digit to "00. " E OFFSET This parameter specifies an offset relative to the external timecode source in hours, minutes, seconds, frames, and subframes. Specify a "+" value to move events forward relative to the incoming timecode. Specify a "­" value to move events backwards relative to the incoming timecode. Press the [ENTER] button to reset the currently-selected digit to "00. " 16 Automix F UPDATE This button determines the fate of events that exist beyond the point at which rerecording is stopped. When the TO END button is on, the DMC1000 V3. 0 erases all events (that exist beyond the point at which rerecording is stopped) for parameters that have been edited during the current pass. [. . . ] Output [+24dBu] +24 +20 +10 +4 0 ­10 ­20 ­30 [+4dBu] Nominal Input GAIN MIN. , PAD ON Nominal Output [+4dBu] [­2dBu] OMNI OUT 1-12 Max. Input [­40dBu] ­40 ­50 Nominal [­60dBu] Input In GAIN MAX. , PAD OFF ­60 ­70 ­80 ­90 ­100 ­110 ­120 ­130 ­140 ­150 ­160 DSP Noise Floor ­170 ­180 ­190 [0dBu = 0. 775Vrms] [0dBFS = Full Scale] For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. [. . . ]