User manual YAMAHA DME64N/24N

[. . . ] Explanation of Graphical Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the top of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 Read these instructions. Install in accordance with the manufacturer's instructions. [. . . ] Edit using the "List Parameters" editing procedure described on page 38. OFF: Set this "OFF" if a digital mixer is not connected directly. Remote: The internal head amp will be controlled from the digital mixer via the [REMOTE] connector. Slot1{Slot1­Slot4 (DME64N)}: The internal head amp will be controlled from the digital mixer via the selected slot. NOTE NO T E This setting applies to individual devices only. Even if one DME64N/24N unit is set to "Disable, " scene store operations will be possible via another DME64N/24N in the same device group that is set to "Enable. " 2 Last Mem. Resume This parameter displays and determines whether the DME64N/DME24N will recall the current scene when started up, or whether the memory contents at the time the unit was turned off will be recalled. The possible settings are "ON" or "OFF". ON: The memory contents at the time the unit was This page will not be displayed on the ICP1. turned off will be recalled at startup. OFF: The current scene will be recalled at startup. NO T E This parameter can be changed from the device group master only. Resume" is set to ON, the unit will back up data to the internal memory periodically. In this case, do not turn off the power to the unit within five (5) seconds after you operate any parameters. HA Control (422) Allows remote head amp control. Always use this setting when a remote head amp unit (AD8HR, AD824) is connected. Also, don't change the setting while a remote head amp is connected. COM (232C) Allows control of DME64N/DME24N units from AMX and Crestron type external controllers using DME Communication Protocol*. CAUTION DME64N/DME24N Owner's Manual 49 Panel Operation and Displays 5 Remote Determines the [REMOTE] connector communication mode. Edit using the "List Parameters" editing procedure described on page 38. Displays the settings of the [REMOTE] terminal. Utility Displays COM (422) Allows from AMX and Crestron type external controllers via the RS-232C interface using DME Communication Protocol*. MIDI (232C) Allows control of DME64N/DME24N units from external MIDI controllers via the RS-232C interface. MIDI (422) Allows control of DME64N/DME24N units from external MIDI controllers via the RS-422 interface. Remote Ctrl (232C) Allows control of DME64N/DME24N units from external devices via the RS-232C interface. Remote Ctrl (422) Allows control of DME64N/DME24N units from external devices via the RS-422 interface. 1 Fs The current sampling frequency of the master word clock. The value shown here is determined by the system's master word clock signal. To select the word clock to be used as the master, move the cursor to the appropriate word clock indication in this display ­ the [WORD CLOCK IN] clock, the cascade clock, or a slot clock, for example ­ and press the [ENTER] key. 2 Int Sets the frequency of the internal word clock ­ 44. 1 kHz, 48 kHz, 88. 2 kHz, or 96 kHz. 3 WCIN Shows the status of the word clock signal at the [WORD CLOCK IN] connector. 4 Cascade Shows the status of the word clock signal at the [CASCADE IN] and [CASCADE OUT] connectors. [. . . ] Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 POLAND Yamaha Music Central Europe GmbH Sp. z. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. [. . . ]