User manual YAMAHA DTX750K ASSEMBLY MANUAL

[. . . ] The sharp holder ends may result in injury. · Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. · If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened firmly. [. . . ] · Do not step on or place heavy objects on the product. · Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc. ) or high humidity (bathroom, outside on a rainy day, etc. ). Doing so may result in deformation, discoloration, damage or deterioration. · When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration. 1. Attach the clamp bolt to each of the tom pads and provisionally tighten (by 5 or 6 turns). 3. If necessary, use clamp bolts A to E to adjust the height and angle of any of the pads. When doing so, be sure to adjust one bolt at a time (i. e. , loosen a bolt, adjust the pad, and then retighten before loosening another). Clamp bolt B Clamp bolt D Clamp bolt E Clamp bolt A Clamp bolt C Clamp bolt (to be tightened in the direction shown) Tom pad (rear side) * Specifications and descriptions in this owner's manual are for information purposes only. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. Continued on other side Mounting the drum trigger module and cymbal pads Mounting the cymbal pads PCY135 PCY155 PCY135 Assembling the kick pad Mounting the snare stand and pad 1. With the stopper making full contact with the bottom surface of the bolt cover, tighten the stopper's key bolt using a tuning key. 1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from scratching. and line up each set nearby in the order in which it was removed. Using a tuning key, loosen the stopper's key bolt. 2. Remove the wing bolts, spring washers, and washers from the kick pad frame, 3. [. . . ] Replace the bolt cover. Bolt cover Felt pad that came with pad unit Insert the 10-channel snake cable's straight plugs into the drum trigger module's trigger input jacks ([q SNARE] to [o KICK/!0] and [HI-HAT CONTROL]). · If you are using the standard setup, the stickers on each of the snake cable's plugs will indicate the name of the corresponding pad. 2. Plug the 10-channel snake cable's L-shaped plugs into the correct pads. [Locations of pad jacks] Pad unit Smaller hole [Drum trigger module's rear panel] Drum trigger module + module stand Stopper Insert Clamp bolt Pad unit 10 9 8 7 6 5 4 3 2 1 Felt pad Cymbal holder Holder clamp Bolt cover Pin Straight plug names (as shown on stickers) DTX700 jack names 1: qSNARE 2: wTOM1 3: eTOM2 4: rTOM3 5: tRIDE 6: yCRASH1 7: uCRASH2 8: iHI-HAT 9: HI-HAT CONTROL 10: oKICK/!0 [10-channel snake cable] Straight plugs Stopper * When assembling the bolt cover, turn until it no longer rotates. Cymbal holder SNARE TOM1 TOM2 TOM3 RIDE CRASH CRASH2 HI HAT HH CON KICK 3. [. . . ]