User manual YAMAHA EMX3000

[. . . ] Owner's Manual INPUT MIC MIC MIC MIC MIC MIC MIC MIC 9L B OUTPUT L 11 L B R ST 1 +4dB L TAPE -10dBV L REC -10dBV FOOT SW L R ST 2 +4dB 10 R B 12 R B R L (MONO) R L (MONO) MONO +4dB LINE LINE LINE LINE LINE LINE LINE LINE 9L (MONO) 11 L (MONO) MONI 1 MONI 2 A A +4dB EFFECT +4dB INSERT IO INSERT IO INSERT IO INSERT IO 0dB INSERT I O 10 R A 12 R A 1 2 3 4 5 OUT IN 6 7 8 R ST SUB 1 +4dB R ST SUB 2 +4dB L R P. AMP IN 9 10 11 12 BRIDGE +4dB C-R PHONES A B A B LIMITER MONI 1 ST LEVEL PEAK GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN +8 +5 +4 POWER +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -34 +10 -34 0 10 0 10 +18 +4 +3 +1 0 -1 -3 -5 -7 -10 L BRIDGE ST1 L MONI 1 MONO (BRIDGE) +18 R ST1 R MONO PEAK PEAK PEAK PEAK PEAK PEAK PEAK PEAK PEAK PEAK PHANTOM +48V (1-8ch) HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH MONI 2 PFL ON OFF C-R/PHONES -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 0 10 TAPE IN MONI 1 MONI 2 POWER AMP ST MID MID MID MID MID MID MID MID MID MID ST -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 0 10 0 10 0 10 0 10 -15 -20 0 10 LOW LOW LOW LOW LOW LOW LOW LOW LOW LOW PFL ST 2 R ON L MIN MAX -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 ST SUB 1 MONI 1 5 4 3 6 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 789 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 1 16 15 125 10 11 12 13 14 PROGRAM 1 VOCAL ECHO 1 2 VOCAL ECHO 2 3 VOCAL ECHO 3 4 VOCAL ECHO 4 PARAMETER 5 VOCAL REVERB 1 6 VOCAL REVERB 2 7 VOCAL REVERB 3 8 VOCAL REVERB 4 ST 1 9 HALL 1 10 HALL 2 11 HALL 3 12 ROOM 0 10 13 PLATE 1 14 PLATE 2 15 PLATE 3 16 GATE REVERB DIGITAL EFFECT 250 500 1K 2K 4K 8K +12 6 0 6 -12 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT ST +12 6 0 ON 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 6 -12 PAN PAN PAN PAN PAN PAN PAN PAN BAL BAL PFL 125 250 500 1K 2K 4K 8K L PFL R L PFL R L PFL R L PFL R L PFL R L PFL R L PFL R L PFL R L PFL R L PFL R ST SUB 2 GRAPHIC EQUALIZER AFL AFL AFL AFL AFL 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 1 2 3 4 5 6 7 8 9 10 11 12 MONI 1 MONI 2 EFFECT ST 1 MONO Keep This Manual For Future Reference. E FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. [. . . ] Use these switches when you wish to monitor a particular output signal through the headphones. MONI 1 MONI 2 EFFECT ST 1 MONO E F G H I s Tape in section E MONI 1 (monitor 1) fader The MONI 1 fader adjusts the final level of the signal sent from the MONITOR 1 bus to the MONI 1 jack (input/output panel 9). If the Power amp select switch V is set to MONI 1MONO, using this fader enables you to adjust the level of the signal sent from the SPEAKER L/ MONI1 1/2 jacks to the speakers. In this section, you can adjust the input level of a cassette deck or a CD player that is connected to the TAPE jacks (input/output panel 5). ST K 0 10 PFL F MONI 2 (monitor 2) fader The MONI 2 fader adjusts the final level of the signal output from the MONITOR 2 bus to the MONI 2 jack (input/output panel 9). L TAPE IN K ST (stereo) control This knob adjusts the level of the signal sent from the TAPE jacks to the STEREO bus. G EFFECT fader The EFFECT fader adjusts the final level of the signal output from the EFFECT bus to the EFFECT jack (input/output panel A). Note: The setting of this fader does not affect the level of the signal sent from the EFFECT bus to the built-in effect. L PFL (pre-fader listen) switch When this switch is on, the signal input from the TAPE jacks is routed at the point before the ST control K to the C-R/PHONES jack (input/output panel B). H ST 1 (stereo 1) fader The ST 1 fader adjusts the final level of the signal sent from the STEREO bus to the ST 1 jacks (input/output panel 8). If the Power amp select switch V is set to ST1 L-ST1 R, this fader also adjusts the level of the signal sent to the SPEAKERS jacks (rear panel 1). Note: The setting of this fader does not affect the signal output from the STEREO bus to the ST 2 jacks. EMX3000--Owner's Manual 4 Front and rear panel s Digital effect section This section enables you to turn the built-in digital effect on/off and select the effect type. s Graphic equalizer section This section enables you to adjust the tone of the STEREO bus signal. M MONI 1 MONI 2 P ST N 125 +12 6 250 500 R 1K 2K 4K 8K +12 6 0 6 -12 S 0 10 0 10 0 10 0 6 ON ON Q MIN MAX VOCAL REVERB 1 VOCAL REVERB 2 VOCAL REVERB 3 VOCAL REVERB 4 -12 6 5 4 3 2 789 1 16 15 10 11 12 13 14 PROGRAM 1 2 3 4 VOCAL ECHO 1 VOCAL ECHO 2 VOCAL ECHO 3 VOCAL ECHO 4 PARAMETER 5 6 7 8 9 10 11 12 HALL 1 HALL 2 HALL 3 ROOM 125 250 500 1K 2K 4K 8K 13 PLATE 1 14 PLATE 2 15 PLATE 3 16 GATE REVERB GRAPHIC EQUALIZER DIGITAL EFFECT R Graphic equalizer This is a 7-band graphic equalizer that allows you to adjust the frequency response of the STEREO bus signal, providing a maximum of ±12 dB of cut/boost for each frequency band. This graphic equalizer affects both the STEREO bus signal that is output to the speakers and the line level signal that is output from the ST 1/2 jacks (input/output panel 8), and MONO jack (input/output panel 0). O M MONI 1/2 (monitor 1/2) control This knob adjusts the level of the return signal that is sent from the built-in digital effect to the MONITOR 1/2 buses. N ST (stereo) control This knob adjusts the level of the return signal that is sent from the built-in digital effect to the STEREO bus. S ON switch This switch turns the graphic equalizer on/off. O PROGRAM selector This knob selects the effect type for the internal digital effect. s Power amp section This section allows you to select the signals that will be sent to the built-in two-channel power amplifier. P ON switch This switch turns the internal digital effect on/ off. Q PARAMETER control This knob adjusts the time parameter of the internal digital effect. Note: The master EFFECT fader setting does not affect the internal digital effect signal. T U +18 LIMITER LEVEL +4 L BRIDGE ST1 L MONI 1 MONO (BRIDGE) +18 +4 R ST1 R MONO V POWER AMP T LIMITER indicator This indicator lights up when the level of the signal output from the power amp section reaches the maximum and the limiter is activated. Adjust the LEVEL control U and appropriate fader so that the indicator lights up for only a short while when the signal reaches the maximum level. Note: The indicator lights up or flashes for a longer duration if the power amp section is significantly overloaded, which could result in malfunction. Avoid such a situation. EMX3000--Owner's Manual Control panel 5 U LEVEL controls These knobs enable you to adjust the level of the signals input from the mixer section to the power amp section. Rotating the knob clockwise will raise the level of the input signal. Use a screwdriver of a width of 3mm or less to adjust the knob. If an external piece of equipment is connected to the P. AMP IN jacks (input/output panel 6), these knobs adjust the input sensitivity of the power amp (the input level that will provide the maximum output level in the power amp section). The sensitivity range is +18 dB~+4 dB, and rotating the knobs clockwise raises the input sensitivity. Note: If the Power amp select switch V is set to MONO (BRIDGE), only the L/BRIDGE LEVEL control becomes effective. s Other indicators and controls W PEAK X POWER PHANTOM +48V (1-8ch) +8 +5 +3 +1 0 -1 -3 -5 -7 -10 -15 -20 L R 0 Y ON OFF C-R/PHONES Z 10 ST 2 [ 0 10 ST 1 W Peak level indicator This indicator allows you to monitor the level of the signal output from the ST 1 jacks. The "0" indicator lights up when the ouput level reaches +4 dB. V Power amp select switch Select one of the following three settings to specify the signals to be routed to the corresponding jacks according to the speaker connection at the SPEAKER jacks 1 on the rear panel. · ST1 L-ST1 R The STEREO bus signals are output from the SPEAKERS L/MONI1 1/2 jacks and the SPEAKERS R/MONO 1/2 jacks. The final level of these signals is adjusted by the master ST 1 fader. · MONI 1-MONO The MONITOR 1 bus signals are output from the SPEAKERS L/MONI1 1/2 jacks, and a monaural signal that is a mix of the STEREO bus signals is output from the SPEAKERS R/MONO 1/2 jacks. The final level of these signals is adjusted by the master MONI 1 fader and the MONO fader. · MONO (BRIDGE) The monaural signal that is a mix of the STEREO bus is output from the BRIDGE jack. [. . . ] If the EFFECT controls are raised, feedback will occur, and your speakers may be damaged. SPEAKERS 1 2 2 L/MONI 1 1 BRIDGE R2 R1 L2 L1 Main speakers Monitor speakers INPUT MIC MIC MIC MIC MIC MIC MIC MIC 9L B OUTPUT L 11 L B R ST 1 +4dB L TAPE -10dBV L REC -10dBV FOOT SW L R ST 2 +4dB 10 R B 12 R B R L (MONO) R L (MONO) MONO +4dB LINE LINE LINE LINE LINE LINE LINE LINE 9L (MONO) 11 L (MONO) MONI 1 MONI 2 A A +4dB EFFECT +4dB INSERT IO INSERT IO INSERT IO INSERT IO 0dB INSERT I O 10 R A 12 R A 1 2 3 4 5 OUT IN 6 7 8 R ST SUB 1 +4dB R ST SUB 2 +4dB L R P. AMP IN 9 10 11 12 BRIDGE +4dB C-R PHONES ST1 L MONI 1 MONO (BRIDGE) POWER PHANTOM +48V (1-8ch) ST1 R MONO A B A B LIMITER MONI 1 ST LEVEL PEAK GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN +8 +5 +4 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -34 +10 -34 0 10 0 10 +18 +4 +3 +1 0 -1 -3 -5 -7 -10 L BRIDGE ST1 L MONI 1 MONO (BRIDGE) +18 R ST1 R MONO PEAK PEAK PEAK PEAK PEAK PEAK PEAK PEAK PEAK PEAK HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH MONI 2 PFL ON OFF C-R/PHONES -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 0 10 TAPE IN MONI 1 MONI 2 POWER AMP ST MID MID MID MID MID MID MID MID MID MID ST -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 0 10 0 10 0 10 0 10 -15 -20 0 10 LOW LOW LOW LOW LOW LOW LOW LOW LOW LOW PFL ST 2 R ON L MIN MAX -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 ST SUB 1 MONI 1 5 4 3 6 MONI 1 Microphone 10 0 10 0 10 0 10 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 789 0 0 10 0 10 0 10 0 10 0 10 0 10 0 10 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 1 16 15 125 10 11 12 13 14 PROGRAM 1 VOCAL ECHO 1 2 VOCAL ECHO 2 3 VOCAL ECHO 3 4 VOCAL ECHO 4 PARAMETER 5 VOCAL REVERB 1 6 VOCAL REVERB 2 7 VOCAL REVERB 3 8 VOCAL REVERB 4 ST 1 9 HALL 1 10 HALL 2 11 HALL 3 12 ROOM 0 10 13 PLATE 1 14 PLATE 2 15 PLATE 3 16 GATE REVERB DIGITAL EFFECT 250 500 1K 2K 4K 8K 88 +12 6 0 6 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT ST +12 6 0 PAN L PFL * Direct box, D. I. * effect unit, pre-amp, etc. 10 0 10 0 10 0 10 0 0 10 0 PAN PAN PAN PAN PAN Effect unit 10 0 10 0 10 0 10 0 10 0 10 6 -12 Effect processor ON -12 125 250 500 1K 2K 4K 8K PAN PAN PAN PAN PFL R L R L R L R L R L PFL R L PFL R L PFL R L PFL R L PFL R ST SUB 2 GRAPHIC EQUALIZER AFL AFL AFL AFL AFL PFL PFL PFL PFL 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 20 25 30 Keyboard 40 50 40 50 Bass guitar 1 2 3 4 5 6 Guitar 7 8 9 10 11 12 MONI 1 MONI 2 EFFECT ST 1 MONO EMX3000--Owner's Manual 14 Example setups s Sending an independent mix to the monitor speakers 1 Set the MONI 1 fader to the "10" position. 2 Raise the MONI 1 controls for the channels that you wish to hear from the monitor speakers. Note: The MONI controls are not affected by the level settings of each channel. This allows you to create a mix that is independent of the main speakers. 3 Use the MONI 1 fader of the master section to adjust the overall volume. s Using an external effect processor You may sometimes want to use an external effect processor, such as an echo machine or a multieffect unit. Follow the steps below. 1 Set the EFFECT fader of the master section to the "10" position. 2 Raise the EFFECT controls for the channels to which you want the external effect to be applied. 3 Use the EFFECT fader in the master section to adjust the level of the signal output to the external effects processor so that the sound will not be distorted at the input of the external effects processor. 4 Use the control of the ST SUB channel to which the processed signal is input from the external effects processor to adjust the level of the effect sound. EMX3000--Owner's Manual Using a subwoofer 15 Using a subwoofer Here is an example of using a subwoofer in the speaker system. 2 R/MONO SPEAKERS 1 2 L/MONI 1 1 BRIDGE R2 R1 L2 L1 Main speakers Yamaha Crossover network PN90 LEFT INPUTS RIGHT TO POWER AMP INPUTS HIGH LEFT RIGHT LOW LEFT RIGHT INPUT MIC MIC MIC MIC MIC MIC MIC MIC 9L B OUTPUT L 11 L B R ST 1 +4dB L TAPE -10dBV L REC -10dBV FOOT SW L R ST 2 +4dB 10 R B 12 R B R L (MONO) R L (MONO) MONO +4dB LINE LINE LINE LINE LINE LINE LINE LINE 9L (MONO) 11 L (MONO) MONI 1 MONI 2 A A +4dB EFFECT +4dB INSERT IO INSERT IO INSERT IO INSERT IO 0dB INSERT I O 10 R A 12 R A 1 2 3 4 5 OUT IN 6 7 8 R ST SUB 1 +4dB R ST SUB 2 +4dB L R P. AMP IN 9 10 11 12 BRIDGE +4dB C-R PHONES A B A B LIMITER MONI 1 ST LEVEL PEAK GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN +8 +5 +4 POWER +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -16 -34 -60 +10 -34 +10 -34 0 10 0 10 +18 +4 +3 +1 0 -1 -3 -5 -7 -10 L BRIDGE ST1 L MONI 1 MONO (BRIDGE) +18 R ST1 R MONO PEAK PEAK PEAK PEAK PEAK PEAK PEAK PEAK PEAK PEAK PHANTOM +48V (1-8ch) ST1 L MONI 1 MONO (BRIDGE) ST1 R MONO HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH MONI 2 PFL ON OFF C-R/PHONES -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 0 10 TAPE IN MONI 1 MONI 2 POWER AMP ST MID MID MID MID MID MID MID MID MID MID ST -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 0 10 0 10 0 10 0 10 -15 -20 0 10 LOW LOW LOW LOW LOW LOW LOW LOW LOW LOW PFL ST 2 R ON L MIN MAX -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 -15 +15 ST SUB 1 MONI 1 5 4 3 6 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 MONI 1 789 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 MONI 2 1 16 15 125 10 11 12 13 14 PROGRAM 1 VOCAL ECHO 1 2 VOCAL ECHO 2 3 VOCAL ECHO 3 4 VOCAL ECHO 4 PARAMETER 5 VOCAL REVERB 1 6 VOCAL REVERB 2 7 VOCAL REVERB 3 8 VOCAL REVERB 4 ST 1 9 HALL 1 10 HALL 2 11 HALL 3 12 ROOM 0 10 13 PLATE 1 14 PLATE 2 15 PLATE 3 16 GATE REVERB Power AMP DIGITAL EFFECT 250 500 1K 2K 4K 8K +12 6 0 6 -12 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT ST +12 6 0 ON 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 6 -12 PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PFL 125 250 500 1K 2K 4K 8K L PFL R L PFL R L PFL R L PFL R L PFL R L PFL R L PFL R L PFL R L PFL R L PFL R ST SUB 2 GRAPHIC EQUALIZER AFL AFL AFL AFL AFL 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 5 10 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 20 25 30 40 50 1 2 3 4 5 6 7 8 9 10 11 12 MONI 1 MONI 2 EFFECT ST 1 MONO Subwoofer EMX3000--Owner's Manual 16 Specifications Specifications s General specifications Maximum output power STEREO: 300 W+300 W/4 @0. 5% THD at 1 kHz 215 W+215 W/8 @0. 5% THD at 1 kHz BRIDGE: 600 W/8 @0. 5% THD at 1 kHz 20 Hz~20 kHz +1 dB, ­3 dB @1 W output into 8 (SPEAKER OUT) Frequency response 20 Hz~20 kHz +1 dB, ­3 dB @+4 dB output into 600 (ST OUT, MONO OUT, EFFECT SEND, MONITOR OUT) Channel Gain control at minimum. Channel Gain control at minimum. Total harmonic distortion Less than 0. 5% @20 Hz~20 kHz, 150 W output into 4 (SPEAKER OUT) Less than 0. 3% @20 Hz~20 kHz, +14 dB output into 600 (ST OUT, MONO OUT, EFFECT SEND, MONITOR OUT) ­128 dB equivalent input noise ­63 dB residual output noise (SPEAKER OUT) ­95 dB residual output noise (ST OUT, MONO OUT, EFFECT SEND, MONITOR OUT) Hum & noise (Average, Rs=150) (with 20 Hz~20 kHz BPF) ­87 dB (ST OUT, MONO OUT) ­64 dB (68 dB S/N) (ST OUT, MONO OUT) ­80 dB (EFFECT SEND, MONITOR OUT) 91 dB 64 dB 38 dB 38 dB 70 dB 64 dB MIC IN to SPEAKER OUT MIC IN to ST OUT LINE IN to ST OUT ST IN to ST OUT MIC IN to EFFECT SEND MIC IN to MONITOR OUT ST master/MONO master fader at maximum level and all channel fader at minimum. [. . . ]