User manual YAMAHA EX5-5R-7

[. . . ] MUSIC SYNTHESIZER/REALTIME CONTROL/EXTENDED SYNTHESIS MUSIC SYNTHESIZER/REALTIME CONTROL/EXTENDED SYNTHESIS TONE GENERATOR/REALTIME CONTROL/EXTENDED SYNTHESIS TONE GENERATOR/REALTIME CONTROL/EXTENDED SYNTHESIS OWNER'S MANUAL SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded/stamped facsimiles of these graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated in the safety instruction section. ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally friendly. [. . . ] 4Select the tempo (tempo track) with the Track parameter. 5Set the first tempo to be recorded, with the Tempo parameter. 6Press either [F7](Replace), or [F8](Punch In), to select the recording mode. If you select Punch In, designate the beginning and end measures for recording (see page 195). Song Mode 9Press [STOP] to stop recording. The EX5/5R/7 automatically returns to Song Play mode. After you have finished recording, there are edit functions that let you edit the Tempo track data in the Song Edit mode (page 201) and the Song Job mode (page 206). When the power is turned off, the song data is lost. Please remember that important song data should be saved to floppy disk or other backup device (page 259). Step Recording: Tr1~Tr16 In Step recording the performance data (note length [gate time], pitch, and velocity) is programmed one note at a time. Step Recording Screen When in Step recording (after you press [PLAY]), the following screen will be displayed. The available keyboard range is from C-1 through B7. 7Press [PLAY], after a two measure countdown recording will begin. The [PLAY] green light will blink in sync with the metronome (Click). During the two measure countdown, Meas (measure) will display the countdown from 2 to 1. Using the Cursor Keys in Step Recording Horizontal cursor [ ] keys: moves to the Measure number, Note Length, Velocity, and Gate Time within the menu. Vertical cursor [vw] keys: selects the input location within a measure. 8Change the tempo by adjusting the tempo value while recording. While recording, without moving the cursor from the Tempo parameter, use Data Dial, [INC]/[DEC], or the numeric keypad to set the tempo. When in the Punch In recording, playback will proceed as usual until the designated beginning measure is reached, at that measure until the end measure, the data will be recorded over (the original data is written over and erased). When the end measure is reached the Punch In record function is cancelled and playback continues if there is recorded data past that point. s Track Number Indicates the track of the currently selected song that is being recorded on. The displayed track number cannot be changed. It is necessary to select the track for recording before entering the Step recording. s Location (Measure, Beat, Clock) Indicates the current cursor position, or the note input location, by displaying the Measure number, Beat, and Clock. You can change the Measure number by moving the cursor to the number using the horizontal cursor key. 198 s Time Signature Displays the time signature of the currently selected song that is being recorded. The displayed time signature cannot be changed. It is necessary to select the time signature for recording before entering the Step recording. s Note Length Sets the length of the note that will be input. After selecting Note Length parameter by using the horizontal cursor keys, designate the note length for each note with the numeric keypad which has different note symbols above each key. You can also use Data Dial or [INC]/[DEC] to adjust the note length in clock units. t Settings: [using the numeric keypad] whole note(1920), half note(960), quarter note (480), 8th note (240), 16th note(120), 32nd notes(60), quarter note triplet(320), 8th note triplet(160), 16th note triplet(80), dotted note; [using Data Dial or [INC]/[DEC]] any numeric value you enter s Beat Graph The Beat Graph lets you confirm and set the note input location within a measure. One small dash "-" indicates the length of a 32nd note. Therefore eight dashes "-" will equal to the length of a quarter note, and 32 dashes "-" will equal to the length of a whole note. [. . . ] Wettergrens Gata 1 Box 30053 S-400 43 Gteborg, Sweden Tel: 031 89 34 00 MALAYSIA Yamaha Music Malaysia, Sdn. , Bhd. 16-28, Jalan SS 2/72, Petaling Jaya, Selangor, Malaysia Tel: 3-717-8977 BRASIL Yamaha Musical do Brasil LTDA. Reboucas 2636, So Paulo, Brasil Tel: 011-853-1377 PHILIPPINES Yupangco Music Corporation 339 Gil J. Box 885 MCPO, Makati, Metro Manila, Philippines Tel: 819-7551 ARGENTINA Yamaha Music Argentina S. A. [. . . ]