User manual YAMAHA FB01

[. . . ] ­ Place only one speaker on each speaker stand. ­ Tighten fastening screws securely. ­ Remove the speakers from the stands before moving the stands or adjusting their height. ­ Add weight such as sand bags around the stand legs to prevent them from falling over. [. . . ] · Before moving the device, remove all connected cables. · Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater) to prevent the possibility of panel disfiguration or damage to the internal components. · Do not place the device in an unstable position where it might accidentally fall over. Connections · Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. · Use only speaker cables for connecting speakers to the speaker jacks. Use of other types of cables may result in fire. · Be sure to observe the amplifier's rated load impedance (see page 4), particularly when connecting speakers in parallel. Connecting an impedance load outside the amplifier's rated range can damage the amplifier. Handling caution · Do not use the device for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. · Do not operate the device if the sound is distorting. Prolonged use in this condition could cause overheating and result in fire. Use either a phone jack or a Neutrik connector to receive input from your sound system/power amplifier. One of the spare connectors can be used to parallel-connect an additional speaker (keeping in mind the impedance considerations mentioned below). MIXING CONSOLE L GRAPHIC EQUALIZER L POWER AMPLIFIER L SPEAKER SYSTEMS R R R SPEAKER SYSTEMS Impedance Considerations When connecting speakers in parallel be sure to check the rated load impedance of the power amplifier. Most power amplifiers are capable of safely driving speakers with minimum impedance of 8 ohms or 4 ohms. A pair of parallel-connected 8-ohm speakers have a total impedance of 4 ohms. The FB01/S115V/SM10V/SM12V/ SM15V/SW115V/SW118V are 8-ohm speakers, and two of these can safely be paralleled on one output. The S215V/SW218V, however, has an impedance of 4 ohms and should not be parallel-connected with another S215V/SW218V or any other model. These models can be connected in parallel, however, if you are using a power amplifier that can safely drive load impedances of 2 ohms or lower. 4 Subwoofers and the P-Series Power Amplifiers ENGLISH Adding subwoofers to speaker systems like the one shown in the diagram can provide superior dynamic range and overall sound quality. After inputting the line-level audio from the preamplifier or mixing console into the Yamaha P-series power amplifiers (P7000S/P5000S/P3500S/P2500S), the separate frequency bands are outputted from the amplifiers. MIXING CONSOLE TWO-CHANNEL GRAPHIC EQUALIZER P-SERIES POWER AMPLIFIERS A A LOW CUT FREQUENCY=90Hz B B SUBWOOFER SPEAKER SYSTEM PARALLEL SUBWOOFER A PARALLEL A LOW CUT FREQUENCY=90Hz SPEAKER SYSTEM B B SUBWOOFER P-SERIES POWER AMPLIFIERS SUBWOOFER 5 Specifications Model Enclosure Speaker Unit LF HF SM10V 10" cone 1" V. C. driver 70Hz-20kHz 125W 250W 500W FB01 12" cone 60Hz-16kHz 175W 350W 700W SM12V S115V Bass reflex type SM15V S215V 15" cone × 2 42Hz-16kHz 500W 1000W 2000W 4 99dB (1W, 1m) 90° 40° 1. 5kHz 15" cone 2" V. C. driver 55Hz-16kHz 250W 500W 1000W Frequency Response Power Capacity NOISE* PGM MAX Nominal Impedance 8 Sensitivity 96dB SPL (1W, 1m) 97dB SPL (1W, 1m) 99dB SPL (1W, 1m) Nominal Dispersion Horizontal 40° 90° 40° 90° 40° Vertical 60° 40° 90° 40° 90° Crossover Frequency 1. 8kHz 2kHz 1. 7kHz Input Connectors 1/4" phone jack × 2, SPEAKON Neutrik NL4MP × 2 Dimensions (W×H×D) 560×353×277 420 × 632 × 333 632 × 414 × 351 489 × 719 × 377 719 × 483 × 343 495 × 1167 × 597 Weight 13. 4kg 20. 8kg 21. 4kg 29. 4kg 28. 0kg 47. 2kg FB01/S115V SM10V/SM12V/SM15V S215V Model Enclosure Speaker Unit Frequency Response Power Capacity SW115V 15" cone 35Hz-2kHz 250W 500W 1000W 8 95dB SPL (1W, 1m) NOISE* PGM MAX SW118V Bass reflex type 18" cone 30Hz-2kHz 300W 600W 1200W SW218V 18" cone × 2 30Hz-2kHz 600W 1200W 2400W 4 98dB SPL (1W, 1m) Nominal Impedance Sensitivity Recommended Crossover Frequency Input Connectors Dimensions (W×H×D) Weight 96dB SPL (1W, 1m) 90Hz, 12dB/oct. 1/4" phone jack × 2, SPEAKON Neutrik NL4MP × 2 506 × 611 × 532 610 × 728 × 641 1221 × 578 × 659 28. 2kg 39. 0kg 65. 4kg Specifications and descriptions in this owner's manual are for information purposes only. [. . . ] Combo Division Viale Italia 88, 20020 Lainate (Milano), Italy Tel: 02-935-771 MALAYSIA Yamaha Music Malaysia, Sdn. , Bhd. Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-78030900 BRAZIL Yamaha Musical do Brasil Ltda. Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi, CEP 04534-013 Sao Paulo, SP. BRAZIL Tel: 011-3704-1377 SPAIN/PORTUGAL Yamaha Música Ibérica, S. A. [. . . ]