User manual YAMAHA FW16E

[. . . ] If it features a 4-pin IEEE1394 connector, use a standard 6-pin to 4-pin IEEE1394 cable. NOTICE Be sure to connect the IEEE1394 cable plug to the IEEE1394 connector in the correct orientation. Plug in the connector in the correct orientation. Precautions Before installing your FW16E expansion board, please read the "Precautions" and "Installation Precautions" sections in your digital keyboard owner's manual. Yamaha cannot be held responsible for damage caused by improper use of or modifications to the device or for data that is lost or destroyed. Installing the FW16E For information on installing the FW16E, refer to the section in the owner's manual of your FW16E-compatible device on "Installing Optional Hardware. " NOTE For optimum results, use an IEEE1394 cable shorter than 4. 5 meters. Before using the FW16E, download the proper Yamaha Steinberg FW Driver from our website: http://www. yamahasynth. com/download/ Specifications Functions Data rate: Audio inputs and outputs: Sampling rates: MIDI connectors: S400 6 Ins, 16 Outs 44. 1 kHz, 48 kHz, 88. 2 kHz, 96 kHz 3 Ins, 3 Outs 6-pin x 2 100P NOTE · Information on system requirements is also available at the above website. [. . . ] This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit "OFF" and "ON", please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna leadin is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. (class B) Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogeräte Befindet sich dieses Symbol auf den Produkten, der Verpackung und/oder beiliegenden Unterlagen, so sollten benutzte elektrische Geräte nicht mit dem normalen Haushaltsabfall entsorgt werden. In Übereinstimmung mit Ihren nationalen Bestimmungen und den Richtlinien 2002/96/EC, bringen Sie alte Geräte bitte zur fachgerechten Entsorgung, Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen. Durch die fachgerechte Entsorgung der Elektrogeräte helfen Sie, wertvolle Ressourcen zu schützen und verhindern mögliche negative Auswirkungen auf die menschliche Gesundheit und die Umwelt, die andernfalls durch unsachgerechte Müllentsorgung auftreten könnten. Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte, kontaktieren Sie bitte Ihre örtliche Stadt- oder Gemeindeverwaltung, Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel. [Information für geschäftliche Anwender in der Europäischen Union] Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder Zulieferer für weitere Informationen. [. . . ] Si desea deshacerse de estos artículos, por favor contacte a sus autoridades locales y pregunte por el método correcto de disposición. (weee_eu) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. [. . . ]