User manual YAMAHA FZR600L

[. . . ] If you have any questions concerning the operation or maintenance of your motorcycle, please consult a Yamaha dealer. The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicable at the date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the recommended maintenance schedules and operating instructions contained within this manual. IMPORTANT MANUAL INFORMATION Particularly important information is distinguished in this manual by the following notations: The Safety Alert Symbol means ATTENTION! [. . . ] Instead, have a Yamaha dealer check the motorcycle. _ _ 1. Spark plug wrench Checking the spark plugs The spark plugs are important engine components, which are easy to check. Since heat and deposits will cause any spark plug to slowly erode, the spark plugs should be removed and checked in accordance with the periodic maintenance and lubrication chart. In addition, the condition of the spark plugs can reveal the condition of the engine. Remove the spark plug as shown, with the spark plug wrench included in the owner's tool kit. Check that the porcelain insulator around the center electrode on each spark plug is a medium-tolight tan (the ideal color when the motorcycle is ridden normally). Check that all spark plugs installed in the engine have the same color. 3. Check each spark plug for electrode erosion and excessive carbon or other deposits, and replace it if necessary. Specified spark plug: CR9E (NGK) or U27ESR-N (DENSO) 6 6-10 PERIODIC MAINTENANCE AND MINOR REPAIR 3. Install the spark plug with the spark plug wrench, and then tighten it to the specified torque. Tightening torque: Spark plug: 12. 5 Nm (1. 25 m·kgf, 9. 0 ft·lbf) NOTE: If a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/4­1/2 turn past finger tight. Remove the oil filter cartridge with an oil filter wrench. NOTE: An oil filter wrench is available at a Yamaha dealer. _ _ _ _ 5. Apply a thin coat of engine oil to the O-ring of the new oil filter cartridge. NOTE: Make sure that the O-ring is properly seated. 6-13 PERIODIC MAINTENANCE AND MINOR REPAIR 8. Add the specified amount of the recommended engine oil, and then install and tighten the oil filler cap. Oil quantity: Without oil filter cartridge replacement: 2. 8 L (2. 46 Imp qt, 2. 96 US qt) With oil filter cartridge replacement: 3. 0 L (2. 64 Imp qt, 3. 17 US qt) Total amount (dry engine): 3. 7 L (3. 26 Imp qt, 3. 91 US qt) ECA00133 _ 1. Install the new oil filter cartridge with an oil filter wrench, and then tighten it to the specified torque with a torque wrench. Tightening torque: Oil filter cartridge: 17 Nm (1. 7 m·kgf, 12 ft·lbf) 7. Install the engine oil drain bolt, and then tighten it to the specified torque. Tightening torque: Engine oil drain bolt: 43 Nm (4. 3 m·kgf, 31 ft·lbf) CAUTION: G In order to prevent clutch slippage (since the engine oil also lubricates the clutch), do not mix any chemical additives. Do not use oils with a diesel specification of "CD" or oils of a higher quality than specified. [. . . ] 5-3 Start switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Steering, checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-36 Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 Storage compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]