User manual YAMAHA G10

[. . . ] The result is better mixes in less time: a huge advantage during high-pressure pre-show setup. StageMix does not provide remote control of all G10 parameters, but is focused on the requirements for adjusting monitor mixes on stage. Yamaha Commercial Audio G10 StageMix V2. 0 User Guide CONTENTS Page 1. 0 2. 0 3. 0 System Requirements Wi-Fi Settings Getting Started 3. 1 G10 Network Setup 3. 2 iPad Wi-Fi Settings 3. 3 StageMix Setup 3. 3. 1 OFFLINE DEMO Mode 3. 3. 2 Configure StageMix to Work with an G10 3. 3. 3 Select a Mixer and Begin Working StageMix Operation 4. 1 Mixer Window 4. 1. 1 Channel Bank Navigation 4. 1. 2 Channel Names 4. 1. 3 Faders 4. 1. 4 Channel ON 4. 1. 5 CUE 4. 1. 6 Master Bank 4. 2 SETUP 4. 2. 1 Fader Delay 4. 2. 2 Filled EQ Graph 4. 2. 3 Set EQ band to 0dB with Double-Tap 4. 2. 4 Enable Inc/Dec Scene Recall 4. 2. 5 Channel Select ­ StageMix Follows Console 4. 2. 6 Channel Select ­ Console Follows StageMix 4. 3 Long Faders 4. 4 HA GAIN 4. 4. 1 Input Port 4. 4. 2 Phantom Power 4. 4. 3 Phase 4. 5 SENDS ON FADERS 4. 5. 1 Mix Send Levels 4. 5. 2 Mix Sends ON 4. 6 EQ Editing 4. 7 Parametric EQ Editing Screen 4. 7. 1 HPF 4. 7. 2 EQ Bands 1 & 4 4. 7. 3 EQ ON 4. 7. 4 EQ FLAT, EQ DEFAULT 4. 8 Graphic EQ Editing Screen 4. 8. 1 Navigation in the GEQ Overview Section 4. 8. 2 Rack Position 4. 8. 3 GEQ Type 4. 8. 4 Editing GEQ Bands 4 4 5 5 5 6 7 7 8 9 9 9 10 10 10 11 11 12 12 12 12 12 12 12 13 14 14 14 15 15 16 16 17 18 19 20 20 20 21 21 21 22 22 Page 2 4. 0 Yamaha Commercial Audio G10 StageMix V2. 0 User Guide 22 22 22 22 23 23 24 24 24 25 25 25 25 26 27 27 27 28 28 29 29 4. 9 4. 8. 5 Navigation in the GEQ Editing Section 4. 8. 6 GEQ ON 4. 8. 7 GEQ FLAT 4. 8. 8 Copy/Paste SCENE MEMORY 4. 9. 1 Current Scene 4. 9. 2 Decrement / Increment Scene 4. 9. 3 Scene List 4. 9. 4 Scene Range 4. 9. 5 Selected Scene 4. 9. 6 Store Scene 4. 9. 7 Undo Store 4. 9. 8 Recall Scene 4. 9. 9 Undo Recall 5. 0 Troubleshooting 5. 1 No Wi-Fi Available 5. 2 Connection Error 5. 3 Connection Lost 5. 4 Graphic EQ Doesn't Affect the Sound 5. 5 Problems Moving Multiple Faders 5. 6 Incompatibility with Earlier G10 Versions Special Notices · The software and this Owner's Manual are the exclusive copyrights of Yamaha Corporation. · Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. · Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software. [. . . ] The gain value of each head amp will be displayed above the fader while any fader cap is being touched. Up to 8 faders can be adjusted simultaneously. Faders will only appear for channels that have a head amp available. In the screenshot above, channel 8 does not have a head amp available. 4. 4. 1 Input Port When HA GAIN mode is active, the input port assigned to each channel will be displayed at the top of each channel strip (the EQ thumbnail is not displayed when HA GAIN mode is active). Note: the Input Port is a display-only parameter and cannot be edited from StageMix. To exit "SENDS ON FADERS" mode, press the [SENDS ON FADERS] button in the left column. Page 16 Yamaha Commercial Audio 4. 6 G10 StageMix V2. 0 User Guide EQ Editing Every channel in the G10 has a dedicated Parametric EQ (PEQ). The G10 also has Graphic EQs (GEQs) that can be assigned (inserted) on input or output channels. Note: assignment of GEQs to channels must be done on the console and cannot be done in StageMix. EQ Curve in Mixer Screen The EQ curve section on the Mixer Screen will show the user whether a GEQ is available on any channel. If GEQ is available on a channel in addition to PEQ, the user will be able to view the curve for either of these EQs and access the editing screen for either type of EQ. Green and blue dots below each EQ curve indicate the types of EQ available on that channel, and the type of EQ (PEQ or GEQ) that is currently displayed for that channel. Or to adjust the frequency without changing the gain. In this case, the "Gain Lock" or "Frequency Lock" functions can be used. These buttons are located at the top of the EQ graph. The "Lock" buttons affect all 4 bands (but not the HPF). When a band is adjusted, the locked parameter value becomes red. 4. 7. 1 HPF When the HPF is selected, an extra [HPF] button appears at the top of the EQ graph. Press this button to switch the HPF on/off. When the button is green, the HPF is On. HPF has no Gain or Q parameter: only frequency. Page 19 Yamaha Commercial Audio G10 StageMix V2. 0 User Guide 4. 7. 2 EQ Bands 1 & 4 EQ bands 1 & 4 have additional choices of band-type. Both these bands can be a shelf or a bell, and band 4 can also be a Low Pass Filter. Band 1 can also be a HPF for Mix, Matrix and Stereo/Mono Master channels. When one of these bands is selected, the relevant additional buttons are shown above the EQ graph. 4. 7. 3 EQ ON The channel EQ can be switched on/off with the [EQ ON] button towards the top-right of the EQ graph. [. . . ] a) Press [STORE] and the iPad's onscreen keyboard will appear. b) To enter a new title for this Scene, tap the X button next to the Scene Title to clear the current title. c) Type in a new title and press the [STORE] button or Return on the keyboard. d) A confirmation popup will appear if the STORE CONFIRMATION preference is ON in the console. [. . . ]