User manual YAMAHA GP800

[. . . ] Because Yamaha has a policy of continuing product improvement, this product may not be exactly as described in this Owner's Manual. Specifications are subject to change without notice. This manual should be considered a permanent part of this water vehicle and should remain with it even if the vehicle is subsequently sold. IMPORTANT MANUAL INFORMATION: In this manual, information of particular importance is distinguished in the following ways: Q The Safety Alert Symbol means ATTENTION! [. . . ] Refer to page 2-9 for correct operation of the device. GU0-023 EJU00454 WARNING 5 4 3 2 1 0 67 8 1000 r/min A/ SET B Multifunction meter Check the operation of multifunction meter. Refer to page 2-13 "MULTIFUNCTION METER" for correct meter operation. MODE C mph GP7-075 3-8 E EJU00455 OPERATION w Before operating your water vehicle, become familiar with all controls. Consult your Yamaha dealer about any control or function you do not fully understand. Failure to understand how controls work could cause an accident or prevent you from avoiding an accident. cC There are two hull drain plugs near the jet unit on the stern side. Be sure they are securely tightened before launching the Water Vehicle. GP7-076 EJU00459 BREAK-IN (RUNNING-IN) PROCEDURE The engine and other components require a break-in (running-in) period to allow surfaces of moving parts to wear in evenly. This ensures proper performance and promotes longer component life. cC 8 During first tankful of operation, use 50 : 1 premix fuel (in addition to oil in oil tank). 8 After above period, use straight gasoline (petrol) for normal operation. 3-9 E 1) Launch the vehicle and start the engine. w Never ride in water that is less than 60 cm (2 feet) deep. You increase your chance of hitting an underwater obstacle. Operate at higher speeds only in deep water free of under water obstacles. 2) 3) 4) Run the engine at the lowest possible speed for the first five minutes. Gradually open the throttle to 3/4 or less. The battery will be quickly discharged, and it will be impossible to start the engine. If the engine does not start after five seconds of cranking, release the starter button. Wait at least 15 seconds before trying to start the engine again. 3-13 E After the engine is warm, push the choke knob in fully, to its original position. NOTE: If the choke knob is left pulled out, the engine will stall. 8) EJU00666a STOPPING THE ENGINE To stop the engine, release the throttle lever, then push and hold the engine stop switch (red button) with your left hand. When the red button is pushed the ignition stops, which stops the engine. GP7-082 NOTE: If leaving the water vehicle, choose the "LOCK" mode on multifunction meter by setting PADLOC, and remove the engine stop switch lanyard to deter unauthorized use. To set the mode, refer to "PADLOC" of "MULTIFUNCTION METER". 3-14 E EJU00466 EJU00472 RIDING YOUR WATER VEHICLE LEARNING TO RIDE YOUR WATER VEHICLE GETTING TO KNOW YOUR WATER VEHICLE Riding your water vehicle requires skills acquired through practice over a period of time. Take the time to learn the basic techniques well before attempting more difficult maneuvers. Riding your new water vehicle can be a very enjoyable activity, providing you with hours of pleasure. But it is essential to familiarize yourself with the operation of the water vehicle to achieve the skill necessary to enjoy riding safely. Before you begin to ride be sure you have read this Owner's Manual completely and understand the operation of the controls. [. . . ] by the selling dealer at the time of your purchase. If you should move after you have purchased your new water vehicle, please advise us of your new address by sending a postcard listing your Yamaha model name, engine number, dealer number [or dealer's name] as it is shown on your warranty card, your name and new mailing address. Mail to: YAMAHA MOTOR CORPORATION, U. S. A. Box 6555 Cypress, California 90630 Attention: Warranty Department This will ensure that Yamaha Motor Corporation, U. S. A. [. . . ]