User manual YAMAHA HTR-5150

[. . . ] U C AT HTR-5150 Natural Sound AV Receiver Ampli-Tuner audio-vidéo OWNER'S MANUAL MODE D'EMPLOI SAFETY INSTRUCTIONS 8 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Ventilation ­ The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. Heat ­ The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. 9 · Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] To tune in to lower frequencies, press the DOWN side of TUNING once. Front panel 1 Select the FM band. Front panel 2 Press TUNING MODE so that the "AUTO TUNING" indicator lights up on the display. Front panel * If TUNING is not pressed, automatic preset tuning soon begins automatically toward the higher frequencies. Automatic preset tuning begins from the frequency currently displayed. Received stations are sequentially stored as A1, A2 . . . * If more than 8 stations are received, they are stored as preset station numbers in other groups (B, C, D and E) in that order. Lights up 3 Press MEMORY and hold for about three seconds. Front panel Flashes If you want to store the first station received by automatic preset tuning as a desired preset station number For example, if you want to store the first received station as C5, select "C5" while "A1", the "MEMORY" indicator and the "AUTO TUNING" indicator flash after pressing MEMORY in step 3. The first received station is stored as C5, and the next stations as sequentially C6, C7 . . . If stations have all been stored up to E8, automatic preset tuning stops automatically. When automatic preset tuning is completed The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure in the section "To recall a preset station" on page 32. 33 Notes · You can manually replace a preset station with another FM or AM station by simply following the procedure in the section "To store stations" on page 31. · Even if the number of received stations is not enough to be stored up to E8, the search is automatically ended after searching all frequencies. · With this function, only FM stations with sufficient signal strength are automatically stored. If the station you want to store is weak in signal strength, tune in to it manually in monaural sound and store it by following the procedure in the section "To store stations" on page 31. EXCHANGING PRESET STATIONS You can exchange the assignment of two preset stations with each other as shown below. 2, 4 Example If you want to change the preset station from "E1" to "A5", or vice versa. 1 2 Recall preset station "E1" by following the procedure in the section "To recall a preset station" on page 32. 3 Next, recall preset station "A5" by following the same procedure as that in step 1. Press EDIT. Front Panel Flashes Flashes 4 Press EDIT once more. Front Panel Shows the exchange of stations has been completed. 34 English SETTING THE SLEEP TIMER The SLEEP timer can be used to make this unit automatically switch to the standby mode. When you are going to sleep while enjoying a broadcast or other desired input source, this timer function is useful. The SLEEP timer can only be controlled with the remote control. Notes · To set the SLEEP timer for this unit, set the SELECTOR DIAL to a position other than the TV position. To set the SLEEP timer for your TV, set the SELECTOR DIAL to the TV position. · The components for which the SLEEP timer is effective are the sources connected to the AC OUTLET(S) on the rear panel of this unit. 1 To set the SLEEP time To cancel the selected SLEEP time Remote control 1 Play the source which you want to enjoy when you are going to sleep and press SLEEP once or more to select the desired SLEEP time. Remote control Press SLEEP once or more so that "SLEEP OFF" appears on the display. (It will soon disappear and the "SLEEP" indicator will go off from the display. ) Note The SLEEP timer setting can also be canceled by setting the unit in the standby mode with STANDBY/ON on the front panel (or STANDBY on the remote control) or by disconnecting the power plug of the unit from the AC outlet. The SLEEP time is displayed. Flashes Each time you press SLEEP, the SLEEP time will change as follows: (Minutes) 120 90 60 30 The SLEEP timer is off (SLEEP OFF). (This is the state before SLEEP is pressed. ) The "SLEEP" indicator soon lights up and the display returns to the indication before the SLEEP timer was set. 2 The unit will be switched to the standby mode automatically at the selected SLEEP time. 35 SOUND FIELD PROGRAM This unit incorporates a sophisticated, multi-program digital sound field processor. This processor allows you to electronically expand and change the shape of the audio sound field from both audio and video sources, creating a theater-like experience in your listening room. You can create outstanding audio sound by selecting a suitable sound field program (this will, of course, depend on what you are listening to) and adding any desired adjustments. The operation of built-in decoders (Dolby Pro Logic, Dolby Digital and DTS) can be controlled by selecting a corresponding DSP program incorporating the combined operation of YAMAHA DSP and Dolby Surround, Dolby Digital or DTS. The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital re-creations of actual acoustic environments. For movie or audio/video sources No. [. . . ] model] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 W [Canada model] . . . . . . . . . . . . . . . . . . . . 310 W/410 VA [Australia and Singapore models] . . . . . 300 W [China and General models] . . . . . . . . . . . . . . [. . . ]