User manual YAMAHA HTR-6030

[. . . ] U HTR-6030 AV Receiver OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS Important safety instructions 10 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 11 · Explanation of Graphical Symbols 12 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 13 1 2 3 4 5 6 7 8 9 Read Instructions ­ All the safety and operating instructions should be read before the product is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. [. . . ] · You can display the XM Satellite Radio information in the front panel display (see page 41). 38 En XM Satellite Radio tuning y When performing these operations with the remote control, press C XM to select "XM" as the input source. 3 All Channel Search mode Press 5 PRESET/TUNING/CH l / h (or G PRESET/CH k / n) repeatedly to change the preset channel number (1 to 8). 1 Press 2 SEARCH MODE (or P SRCH MODE) repeatedly to select "ALL CH SEARCH". Press 5 PRESET/TUNING/CH l / h (or G PRESET/CH k / n) repeatedly to search for a channel within all channels. y You can also select the preset channel number directly by pressing the numeric buttons (1 to 8) on the remote control. Direct Number Access mode 2 1 2 Press P SRCH MODE repeatedly to select "ALL CH SEARCH" or "CAT SEARCH". Press the numeric buttons (V) to enter the desired three-digit channel number. For example, to enter the number 123, press the numeric buttons as shown below. l h ENHANCER y · You can search for a channel quickly by pressing and holding 5 PRESET/TUNING/CH l / h (or G PRESET/CH k / n). · To display the XM Radio ID number displayed in the front panel display, select channel "0". Category Search mode 1 BASIC OPERATION 2 3 1 2 3 Press 2 SEARCH MODE (or P SRCH MODE) repeatedly to select "CAT SEARCH". l / h) repeatedly to change the channel category. Press 5 PRESET/TUNING/CH l / h (or G PRESET/CH k / n) repeatedly to search for a channel within the selected channel category. The display changes as follows. <XM> --1 y You can search for a channel quickly by pressing and holding 5 PRESET/TUNING/CH l / h (or G PRESET/CH k / n). <XM> -12 Preset Search mode Prior to selecting a preset channel in the Preset Search mode, you must preset XM Satellite Radio channels. For details, see "Setting XM Satellite Radio preset channels" on page 40. y All preset channels (A1 to E8) recalls "001 Preview" by the initial factory setting. <XM>123 y · To enter a one-digit or two-digit channel number, press the numeric buttons (V) and then press W ENT. to tune into the channel immediately, you can wait a few seconds until this unit confirms the entered channel number. · If no button is pressed within a few seconds after you enter a one-digit or two-digit number, this unit automatically confirms the entered channel number. · Pressing a button other than the numeric buttons (V) or W ENT. cancels the Direct Number Access mode procedure. 1 Press 2 SEARCH MODE (or P SRCH MODE) repeatedly to select "PRESET SEARCH". l / h) repeatedly to change the preset channel group (A to E). 2 English 39 En XM Satellite Radio tuning Setting XM Satellite Radio preset channels You can use this feature to store up to 40 XM Satellite Radio channels (A1 to E8: 8 preset channel numbers in each of the 5 preset channel groups). You can then recall any preset channel easily by selecting the preset channel group and number as described in "Preset Search mode" on page 39. 4 Press 5 PRESET/TUNING/CH l / h (or G PRESET/CH k / n) repeatedly to select a preset channel number (1 to 8) while the MEMORY indicator is flashing. The preset channel number appears in the front panel display. Flashes MEMORY 1 Search for a channel you want to set as a preset channel by using one of the XM Satellite Radio search modes. See "Basic XM Satellite Radio operations" on page 38 for details. The MEMORY indicator flashes in the front panel display for approximately 10 seconds. Note You must proceed to and carry out steps 3 through 5 while the MEMORY indicator is flashing in the front panel display. C5 [043] XMU Currently selected preset channel number 5 2 Press 6 MEMORY (or H XM MEMORY) to set the selected XM Satellite Radio channel as a preset channel while the MEMORY indicator is flashing. A colon (:) appears next to the preset channel number for confirmation, and the MEMORY indicator turns off in the front panel display. C5:[043] XMU Colon (:) 3 Press 4 CATEGORY (or G A-E/CAT. l / h) repeatedly to select a preset channel group (A to E) while the MEMORY indicator is flashing. The preset channel group letter appears in the front panel display. Flashes Note Once you set a new preset channel, the one previously stored in the same preset channel group and number is cleared. MEMORY C [043] XMU Currently selected preset channel group 40 En XM Satellite Radio tuning Displaying the XM Satellite Radio information You can display the XM Satellite Radio information (such as channel number, channel name, category, artist name, or song title) for the currently selected channel in the front panel display. [. . . ] 28 Selecting the night listening mode . . . . . . . 28 Selecting the SCENE templates . . . . . . . . . . . 23 Set menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Set this unit to the standby mode . . . . . . . . . [. . . ]