User manual YAMAHA KX-W382

[. . . ] 10 Power Sources -- The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ÷ Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 11 Power-Cord Protection -- Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying attention to receptacles, and the point where they exit from the unit. 12 Cleaning -- The unit should be cleaned only as recommended by the manufacturer. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. 13 No Use Periods -- The power cord of the unit should be unplugged from the outlet when left unused for a long period of time. 14 Object and Liquid Entry -- Care should be taken so that objects do not fall into and liquids not spilled into the inside of the unit. 1 Read Instructions -- All the safety and operating instructions should be read before the unit is operated. 15 Damage Requiring Service -- The unit should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged; or B. [. . . ] No change in any of the other connections between the deck and amplifier/receiver, etc. , is necessary. TIMER NATURAL SOUND STEREO CASSETTE DECK KX-493 STANDBY/ON INTRO SCAN TIMER REC OFF PLAY COUNTER RESET MEMORY REPEAT AUTO TAPE OFF/0-M/FULL TUNING DOLBY NR OFF/ B/ C/MPX PHONES LEVEL BIAS ADJUST 0 PLAY TRIM 0 BALANCE 0 REC LEVEL EJECT YAMAHA GF Head Cassette Stabilizer REC/PAUSE MUTE/SEARCH MIN MAX ­ + ­ + L R MIN MAX To an AC outlet Tuner Amplifier or receiver Audio timer Timer recording 1. After turning on the power to each component, select the station on your tuner which you want to record and turn down the volume on your amplifier/receiver. This will have no effect on the recording signal level. Remember to set the proper recording level. Set the timer to the desired recording start and stop times. It is advisable to set the timer to begin recording slightly before and end slightly after the actual broadcast receiving time to leave some room for later editing. Set the TIMER switch to the REC position. TIMER REC OFF PLAY Timer playback 1. Turn on the amplifier/receiver and adjust the volume and tone controls. Set the input mode selector of your amplifier/receiver to the cassette deck function mode. Set the timer to the time you wish to start and stop playback. Set the TIMER switch to the PLAY position. TIMER REC OFF PLAY 5. This effect may be compensated for somewhat by adjusting the BIAS ADJUST to the plus (+) direction during recording, or by using the PLAY TRIM control and/or the tone controls of your amplifier/receiver during playback. TYPE II TYPE IV TAKING UP SLACK IN THE TAPE As a precaution against tape entanglement and damage, remove any slack in the tape before inserting cassettes into the deck. This is accomplished by inserting a pencil, pen or similar object into one of the spools and gently winding it until all the slack is removed. Be careful not to touch the tape part itself. It is very delicate and touching it may damage the tape and its recorded contents. Detector slots Detector slots STORING CASSETTES After putting a cassette tape back into its case, store it in a location away from exposure to direct sunlight, humidity, high temperatures, and magnetic fields (away from television sets, speakers, etc. ). High temperatures and humidity will damage the tape itself, while exposure to magnetic fields may cause a loss of recorded material. Avoid touching the tape surface with your fingers, since dirt or finger oil will contaminate the deck's heads. 14 To open the sub panel To close the sub panel OPTIONAL REMOTE CONTROL TRANSMITTER With the optional remote control transmitter RKX1, you can operate this unit at your listening position. For details, refer to the instruction manual supplied with the remote control transmitter. REMOTE CONTROL OPERATION RANGE Remote sensor ¤ SINGLE DECK INTRO SCAN < DOUBLE DECK DUBBING DECK A/B DIR A DIR B COUNTER ! SEARCH / PLAY RESET ! / 7 m (23 feet) 30° REC/PAUSE REC MUTE STOP RKX1 s 30° MAINTENANCE CLEANING OF THE TAPE PATH Continued high quality performance of your deck is dependent upon periodic cleaning of the heads, capstan, pinch roller, and all surfaces over which the tape travels. Normal use will cause an accumulation of dirt and dust on the heads, capstans, and pinch rollers. This can lead to poor sound quality, drop outs (intervals with no sound), unsteady tape speed, loss of high frequency response, etc. Thus, clean the heads and all surfaces over which the tape travels with a commercially available cleaning cassette and fluid type cleaner. Inside of the cassette compartment Heads Capstan Pinch roller DEMAGNETIZATION After 20-30 hours of use, enough residual magnetism will build up on the heads to cause poor high frequency reproduction. [. . . ] 20 ~ 17. 000 Hz ±3 dB Bande CrO2 (­20 dB) . . . . . . . . . . . . . . . . 20 ~ 18. 000 Hz ±3 dB Bande métal (­20 dB) . . . . . . . . . . . . . . . 20 ~ 20. 000 Hz ±3 dB <KX-W382> Bande normale (­20 dB) . . . . . . . . . . 20 ~ 16. 000 Hz ±3 dB Bande CrO2 (­20 dB) . . . . . . . . . . . . . . . . [. . . ]