User manual YAMAHA LP-7A/LP-5A ASSEMBLY INSTRUCTIONS

[. . . ] · Future upgrades of application and system software and any changes in specifications and functions will be announced at the following URL. http://www. yamahaproaudio. com/ · The illustrations and screens as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your computer. · Windows is a registered trademark of Microsoft® Corporation in the United States and other countries. · The company names and product names in this manual are the trademarks or registered trademarks of their respective companies. [. . . ] When this is off, the volume will be as specified by the on-screen faders; the volume will not match the settings of the LP-7A/LP-5A's volume knobs. When you save settings to memory, the on-screen fader values will be saved. The [LINK] button will return to the On (green) state when you close LP-7A/LP-5A Manager or return to the starting screen. If the volumes would increase when you switch this from off to on, a confirmation screen will appear. If the [LINK] button is on (green), this will be inoperable. Parameter Fader Level Range - ­ +10dB Default ­ Markers The red marker indicates the setting of the LP-7A/LP-5A's volume knob; the blue marker indicates the volume value saved in memory. [LOCK] button If you turn this off (gray), operations of the volume knob for that channel will be effective if the LP-7A/LP-5A is locked by its LOCK switch. If this is on (red), volume knob operations for that channel will be ignored. 6 [MATRIX] button Opens the MATRIX screen (page 17). Here you can specify the output channels to which the input channel signals are sent. 7 [STEREO/MONO] button Specifies whether OUTPUT channels 1 and 2 deliver a STEREO or MONO output signal. When [STEREO] is selected the left (L) signal is output to channel A and the right (R) signal is output to channel B. 8 [EQ+FILTER] button Opens the OUTPUT EQ screen (page 19). Here you can edit the parameters of the 6-band equalizers provided for OUTPUT channels 1 through 4. 9 [DELAY] button Opens the "DELAY" dialog box, allowing you to specify the delay time for each OUTPUT channel. Use these settings when you need to apply a delay to the main speaker outputs so that the sound from the sub-speakers will not be heard with a timing offset. If excessive input level is indicated, either reduce the output level of the connected source, or reduce the input level via the appropriate rear-panel [PAD] (34 dB) switch or by using INPUT GAIN. NOTE · dBFS stands for "decibels full scale, " and indicates the digital audio level. 0 dBFS is the maximum level. 5 [EQ] button This button opens the "INPUT EQ" dialog box, where you can edit the EQ that is provided on each input channel. This is the same as the BLOCK screen's "INPUT EQ" dialog box; refer to page 13 for details. 6 [F. B. SUP] button This turns the feedback suppressor on/off (MONO INPUT channels only). The on/off state of this button is linked with the Feedback Suppressor check box in the MISC screen. For more about the Feedback Suppressor, refer to page 22. LP-7A/LP-5A Manager Owner's Manual 16 7 [PRIORITY]/[OVERRIDE] button This turns on/off the Priority Ducker function (MONO INPUT channels only) or the Music Override function (STEREO INPUT channels only). The on/off state of this button is linked with the Priority Ducker Key Source Select or Music Override Key Source Select check boxes in the MISC screen. For more about the Priority Ducker function and Music Override function, refer to page 21. 8 [OUT1]­[OUT4] buttons Here you can specify the output channels (OUTPUT channels 1- 4) to which the input channel signals are sent. These settings are linked with the matrix settings in the MATRIX screen. 9 [LINK] button, fader, marker, [LOCK] button Here you can adjust the volume of the input channel. These parameters are the same as in the BLOCK screen's "LEVEL" dialog box; refer to page 14 for details. MATRIX screen Here you can specify the output channels to which the input channel signals are sent. The send levels from MONO INPUT channels to the OUTPUT channels can also be adjusted here. 1 2 NOTE · From the LP-7A/LP-5A's panel, you can temporarily turn on a send from a specific input channel to an OUTPUT channel. [. . . ] · You may not use the SOFTWARE to distribute illegal data or data that violates public policy. · You may not initiate services based on the use of the SOFTWARE without permission by Yamaha Corporation. Copyrighted data, including but not limited to MIDI data for songs, obtained by means of the SOFTWARE, are subject to the following restrictions which you must observe. · Data received by means of the SOFTWARE may not be used for any commercial purposes without permission of the copyright owner. [. . . ]