User manual YAMAHA LPX-510

[. . . ] URTG LPX-510 Home Cinema Projector ENGLISH OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. · 1 2 3 4 5 6 7 8 Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 9 10 11 12 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. IMPORTANT! Please record the serial number of this unit in the space below. Model: Serial No. : The serial number is located on the bottom of the unit. [. . . ] If the projector is in standby mode, press the [STANDBY/ON] button on the projector's control panel or the button on the remote control to start projection. The purpose of this command is to extend the lamp's useful life. It lets you set the power supplied to the lamp to one of 6 levels to adjust the lamp brightness. If the adjustment value is set to "75", the power supplied to the lamp is reduced by about 25%. This sets the standby conditions that are activated when the power is turned off. If set to "RS-232C Off", the power output in standby mode becomes 0. 4 W. If set to "RS232C On", the power output in standby mode becomes 3. 0 W. Set to "RS-232C On" if you would like the projector to be able to receive communication commands when the power is turned off. When this setting is changed, turn off the power, and when the cool-down period has finished, turn the power back on again. The new setting will be applied after the power turns back on. This sets whether or not a 12 V signal is output from the TRIGGER OUT port to external equipment in synchronization with the operation of the lamp and fan. When set to "RS232C", it turns trigger output on and off by means of control signals from the RS-232C port. When this setting is changed, turn off the power, and when the cool-down period has finished, turn the power back on again. The new setting will be applied after the power turns back on. This lets you turn the settings for the various lock functions on and off. When a lock function is on, a icon appears on the screen when a button is pressed. · Focus Lock : Focus adjustment is disabled. · Zoom Lock : Zoom adjustment is disabled. · Key Lock Default setting OFF Lamp Power 100 (Depends on picture mode) RS-232C Off Standby Mode Trigger Out Lamp Lock Setting OFF OFF OFF : If this is set to "ON", you can't operate the projector's control panel buttons. If you change the setting, the new setting will take effect after exiting the configuration menu. (To cancel) Use the remote control to return the setting to "OFF". LCD Panel Adjustment If vertical interference appears in the projected images, use this setting to remove it. · Vertical Stripe Adjustment R: While checking the red tone adjustment screen, adjust until the stripes are no longer noticeable. · Vertical Stripe Adjustment G: While checking the green tone adjustment screen, adjust until the stripes are no longer noticeable. · Vertical Stripe Adjustment B: While checking the blue tone adjustment screen, adjust until the stripes are no longer noticeable. 34 Using the Menu Functions User's Logo You can record your favorite image as a user's logo. A user's logo can be stored for projecting when the projector starts up and when projecting the hide screen. When a user's logo is recorded, the previous user's logo will be erased. [. . . ] The image size will be reduced when keystone correction is carried out. 3 Setting-up Methods The projector supports the following 4 projection methods, allowing you to choose the best method for displaying your images. After setting up the projector, refer to the OWNER'S MANUAL for details on turning on the power and adjusting settings such as the screen size. ("Basic Operations" in OWNER'S MANUAL) Be sure to read "Caution" in OWNER'S MANUAL for details on safe handling when setting up the projector. Front projection Front/ceiling projection Rear projection using a translucent screen Rear projection onto a translucent screen with the projector installed to the ceiling *1 If the projector is projecting from above or below the screen or from the side of the screen, use the lens shift function to adjust the image projection position. (OWNER'S MANUAL "Adjusting the screen image" Adjusting the projection position (lens shift) ) *2 When installing to the ceiling or projecting from behind the screen, set the "Projection" command in the menu ("Setup" - "Screen" - "Projection") to match the method of projection being used. [. . . ]