User manual YAMAHA M3000-40C M3000-24

[. . . ] MIXING CONSOLE Owner's Manual Mode d'emploi Bedienungsanleitung M FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. [. . . ] However even in this case, if the AFL switch (6) is turned on, the signal before passing through the LEVEL control can be monitored from the MONITOR OUT jacks or the PHONES jack. 1 2 3 4 5 M1 M2 M3 M4 E LEVEL control This adjusts the final output level of the corresponding matrix 1­8. The "w" position is nominal level (0 dB). M5 M6 M7 M8 M9 M10 M11 M12 M13 M14 M15 M16 STEREO A L STEREO A R SUB IN L SUB IN R AFL LEVEL ON to Meter MATRIX OUT 1-8 MAS MAS PFL AFL AFL PFL L R ON L R L R ON L MATRIX SUB IN R BA BA 24 Control panel Meter bridge A B C 20 10 PEAK 2 75 3 101 2 PEAK 3 20 10 7 2 3 20 10 PEAK 2 75 3 101 2 3 20 10 PEAK 2 75 3 101 2 3 20 10 PEAK 2 75 3 101 2 3 20 10 PEAK 2 75 3 101 2 3 20 10 PEAK 2 75 3 101 2 3 ­ VU M1/M9/MATRIX 1 + ­ + ­ VU + ­ VU L + ­ VU R + ­ VU L + ­ VU R + M2/ IX 7 M8/M16/MATRIX 8 STEREO A STEREO B/CUE A M1/M9/MATRIX1­M8/M16/MATRIX8 level meters As selected by the switch settings of the METER SEL section (page 22), these meters indicate the output levels of MIX OUT 1­8/MIX OUT 9­16/MATRIX OUT 1­8. Each meter has a PEAK indicator which lights 3 dB before peak level. B STEREO A level meters These meters indicate the output levels of the signal which is output from the STEREO OUT A jacks. Each meter has a PEAK indicator which lights 3 dB before peak level. C STEREO B/CUE level meters Normally, these meters indicate the output levels of the signal which is output from the STEREO OUT B jacks. However if the PFL switch of an input channel or an AFL switch in the mix section or matrix section etc. has been pressed and you are monitoring the PFL bus, the MAS PFL bus, or the MAS AFL bus, these meters will indicate the level of the signal which is being monitored. Each meter has a PEAK indicator which lights 3 dB before peak level. 25 Rear panel Mono input channel input/output jacks INSERT OUT IN Stereo input channel input/output jacks INSERT OUT IN H3 TA ST CH 2 INPUT A ST CH 1 INPUT A 24 23 22 21 4 3 2 1 ST CH 4 INPUT A ST CH 3 INPUT A ST CH 2 INPUT A ST CH 1 INPUT A L L INPUT INPUT INPUT INPU NPUT INPUT INPUT INPUT A R R DIRECT OUT DIRECT OUT DIRECT OUT DIRECT 0 dB 0 dB 0 dB 0 dB L L L L 4 R R R R L R INPUT B L R INPUT B L R INPUT B L R INPUT B ECT OUT DIRECT OUT DIRECT OUT DIRECT OUT 0 dB 0 dB 0 dB L R TB INPUT B L R INSERT I/O INSERT I/O 0 dB INSERT I/O 0 dB INSERT 0 dB ERT I/O INSERT I/O 0 dB INSERT I/O 0 dB INSERT I/O 0 dB B C INPUT B 0 dB 5 A INPUT jacks These are XLR-3-31 type input jacks (balanced). Nominal input level is ­16 dB ~ ­60 dB when the 26 dB pad switch (page 6) is off, or +10 dB ~ ­34 dB when the pad switch is on. When the rear panel PHANTOM MASTER switch and the phantom power switches for the corresponding input channel are on, +48 V phantom power is supplied. Pin wiring is as follows. Male XLR plug 1 (ground) 3 (cold) D INPUT A jacks These are XLR-3-31 type input jacks (balanced). Nominal input level is +10 dB ~ ­30 dB. To use these jacks, you must set the A/B select switch of the corresponding stereo input channel to the A position. Pin wiring is as follows. Male XLR plug 1 (ground) 3 (cold) 2 (hot) E INPUT B jacks 2 (hot) B DIRECT OUT jacks These are 1/4" phone jack direct outputs (unbalanced). Pin wiring is as follows. Tip (send) 1/4" phone plug These are RCA phono input jacks (unbalanced). Nominal input level is +10 dB ~ ­20 dB. To use these jacks, you must set the A/B select switch of the corresponding stereo input channel to the B position. Pin wiring is as follows. Phono plug Tip Sleeve Sleeve (ground) With the factory settings, the post-fader signal is output. However by changing internal jumpers, you can switch this so that the pre-EQ or pre-fader/post EQ signal is output. If you wish to change internal jumper settings, please contact your dealer. C INSERT I/O jacks These are TRS phone jacks which allow an external effect processor to be inserted into each mono input channel. Pin wiring is as follows. Tip (send) 1/4" phone plug Tip (send) Ring (return) To processor's input 1/4" TRS phone plug Sleeve (ground) Sleeve (ground) Tip (return) 1/4" phone plug Connect to INSERT I/O jack From processor's output Sleeve (ground) 26 Rear panel Master section input/output jacks QNML R U MIDI CONTROL 2TR IN L IN PHANTOM MASTER ON OFF J 5 I MIX OUT +4dB 1 13 9 5 1 G ST INSERT I/O 0dB F MIX INSERT I/O 0dB MONITOR ST OUT+4dB OUT+4dB L L MATRIX OUT+4dB 1+4dB OUT A R R R 6 2 14 10 6 2 THRU VCA EXTERNAL I/O L MASTER SLAVE VCA MASTER/SLAVE 7 3 15 11 7 3 MATRIX SUB IN 2­10dBV B R 8 4 16 12 8 4 +4dB CUE CONTROL S R DC POWER INPUT +4dB L R +4dB L 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 CUE SUB IN ST SUB IN MIX SUB IN +4dB VT F MIX INSERT I/O jacks P O K I MIX OUT jacks H These are TRS phone jacks for inserting external signal processors into MIX buses 1­16. Pin wiring is as follows. Tip (send) 1/4" phone plug These are XLR-3-32 output jacks (balanced) for individually outputting the signals of MIX buses 1­16. Pin wiring is as follows. Female XLR plug 2 (hot) 3 (cold) Tip (send) Ring (return) To processor's input 1/4" TRS phone plug Sleeve (ground) Sleeve (ground) Tip (return) 1/4" phone plug Connect to INSERT I/O jack 1 (ground) From processor's output Sleeve (ground) G STEREO INSERT I/O jacks These are TRS phone jacks for inserting external signal processors into the ST bus. [. . . ] *3 INSERT Phone Jacks(TRS) are unbalanced(T=OUTPUT, R=INPUT, S=GND). *4 Stereo Phone Jack is unbalanced. 43 Specifications Other Connector wiring DC POWER INPUT Pin No. 1 2 3 4 5 6 7 8 9 10 Signal name Power supply remote +15 V ±15 V GND +48 V GND ­15 V +12 V +12V GND/ power supply remote Power supply remote +48 V FRAME GND 3 7 10 6 2 5 9 1 4 8 VCA EXTERNAL I/O Pin No. 1 2 3 4 5 6 7 8 9 Signal name VCA GROUP 1 VCA GROUP 2 VCA GROUP 3 VCA GROUP 4 VCA GROUP 5 VCA GROUP 6 VCA GROUP 7 VCA GROUP 8 GND 1 2 3 4 5 6 7 8 9 Included items Power supply connection cable (3 m, 10 pin) 44 Dimensions W: 2043/40ch H: 265 W: 1515/24ch Units: mm D: 874 45 MIDI data format 1. [. . . ]