User manual YAMAHA MAGICSTOMP GUITAR EFFECTS PROCESSOR MK2

[. . . ] GUITAR EFFECTS PROCESSOR FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. [. . . ] Using another adaptor may result in damage, overheating or fire, which can be very dangerous. · Make sure to use the recommended AC voltage as indicated on the power adaptor. · The MAGICSTOMP automatically switches "ON" when power is connected and supplied to the device. · Connect a guitar, bass or any line level instrument such as a synthesizer, etc. , to the INPUT jack. The MAGICSTOMP can also be connected to the effect loop of an amplifier, mixer, or other similar device. · Set the INPUT LEVEL switch to match the output level of the instrument or device that is connected to the MAGICSTOMP. If the sound is distorted when the switch is set to the HIGH position, change the setting to LOW. If you feel output is low when the switch is set to the LOW position, change the setting to HIGH. · When using patches with stereo output, we recommend connecting the MAGICSTOMP's output jacks to a stereo device. · When connecting to a monaural device, use the OUTPUT L/MONO jack. · When connecting the power adaptor to the MAGICSTOMP's AC IN jack, you can wrap the power adaptor cord around the cord hook as shown in the illustration below (this helps keeping the plug from being accidentally pulled out). CAUTION · Don't let the cord bend sharply or kink when wrapping the cord around the hook. An excessive bend can cut the cord or start a fire. AC IN jack Cord hook Power adaptor cord 10 Connections Using the MAGICSTOMP with a guitar or other instrument Connecting to a guitar amplifier (monaural) INPUT Connecting to guitar amplifiers (stereo) INPUT INPUT Connecting to a recording device, etc. INPUT INPUT L/MONO L/MONO R L/MONO R OUTPUT L/MONO R AC IN INPUT Guitar, or other instrument * The AC adaptor's shape will vary according to the country to which the device is shipped. Power Adaptor Electric Outlet U99¤MAGICSTOMP óGAINfiMSTRáTONE MAGICSTOMP Using the MAGICSTOMP in an effect loop Power Adaptor Electric Outlet * The AC adaptor's shape will vary according to the country to which the device is shipped. OUTPUT L/MONO AC IN R INPUT EFFECT SEND EFFECT RETURN L R U99¤MAGICSTOMP óGAINfiMSTRáTONE MAGICSTOMP Mixer, etc. 11 Using the MAGICSTOMP The MAGICSTOMP comes loaded with a variety of effect patches (programmed effects). First, give some of the presets a try and see what's available. Turn on the amplifier and play You'll hear the currently selected patch. Use the MAGICSTOMP's VOLUME knob to adjust the MAGICSTOMP's output volume. Patch No. Patch Name U99¤MAGICSTOMP0 óGAINfiMSTRáTONE Try out some of the other patches The MAGICSTOMP has a total of 198 patches. 99 of those are User Patches (U01 ­ U99) to which you can save (overwrite) data of patches that you have created. The other 99 are Preset Patches (P01 ­ P99) which can not be overwritten with new data. You can however, edit the Preset Patches and save them in the User Patch section. * When shipped from the factory, the MAGICSTOMP's User Patch section contains the same data as found in the Preset Patches. Two ways to select patches When the MAGICSTOMP is shipped from the factory, its [UP/DOWN MODE] is already set for the patch selection mode. In this mode, just press the + switch to move to the next greater patch number, and press the ­ switch to move to the next lesser patch number. Hold either switch down and the patch numbers will quickly cycle up or down in order. In this mode, the ON/OFF switch is used to switch the patch (effect) on or off. Pressing the ­ switch decreases the patch number by 1 U01 U98 U99 P01 P97 P98 P99 U01¤DIST óBAL0fiSTERáVOL Pressing the + switch increases the patch number by 1 P99 P02 P01 U99 U04 U03 U02 Effect ON Effect OFF U01¤DIST óGAINfiMSTRáTONE U01¤DIST ó EFFECT OFF 12 Using the MAGICSTOMP The other way to select patches is with the [Performance Mode]. In this mode, the ­, +, and ON/OFF switches are used to turn three adjacent patches ON and OFF. q To enter the Performance Mode, press and hold any two switches (from ­, +, and ON/OFF). "PERFORMANCE MODE" appears in the display to inform you that the MAGICSTOMP is now in the Performance Mode. w Press and hold the ­ or + switch to change the patch set. ­ switch: U01/02/03P97/98/99P94/95/96. . . [. . . ] If the MAGICSTOMP is in its Tuner Mode (P. 20) or Name Edit Mode (P. 18) you can not change to another patch. · Adjusting the control knob has no effect on the sound Rotate the knob until the value shown on the display changes, and then try setting. (P. 14) 28 Specifications Digital Section · Digital signal processing effector · Includes special editor application "Sound Editor for MAGICSTOMP" · Patch Select: 2 Modes · Built-in Chromatic Auto Tuner Sampling Frequency 44. 1 kHz Memory Allocations Preset: 99 User: 99 Communications Receive: Parameter Change, Bulk In (1 patch), Bulk In (99 patch) Transmit: Bulk Out (99 patch) Input Level/Impedance INPUT HIGH: -25dBm/1 M INPUT LOW : -15dBm/1 M Controller/Switch Knob x4 CONTROL1, 2, 3, VOLUME Push Switch x4 ­, +, ON/OFF, STORE Slide Switch x1 INPUT LEVEL (HIGH/LOW) Output Level/Impedance OUTPUT L/MONO, R: 0dBm/1 k Power Power Adaptor AC Output: AC 12 V, 1 A Power Consumption 12 W Display 16 x 2 character LCD (w/Back light) LED x 3 (­, +, ON/OFF) Dimensions (W x H x D) 164 x 62 x 176 mm (6-7/16" x 2-7/16" x 6-15/16") Connections INPUT: Standard Monaural Phone Jack OUTPUT L/MONO, R: Standard Monaural Phone Jack USB AC IN Weight 910 g (2lbs. ) Accessories AC-10 power adaptor (included or optional depending on local) CD-ROM USB Cable Owner's Manual (this booklet) Patch List A/D Converter 24 bit + 3 bit Floating D/A Converter 24 bit * Specifications and design may change without notice. 29 SOFTWARE LICENSING AGREEMENT The following is a legal agreement between you, the end user, and Yamaha Corporation ("Yamaha"). The enclosed Yamaha software program is licensed by Yamaha to the original purchaser for use only on the terms set forth herein. Please read this licensing agreement with care. [. . . ]