User manual YAMAHA MBL-25A MBL-32A MBL-832A MXL-25A MXL-32A MXL-32AF

[. . . ] (The settings for “Left” (channel) are also applied to “Right” (channel), even though that channel does not appear on the screen. ) If the values for all channels on a bus are not the same, an asterisk (*) is added after the parameter. (“HA GAIN*”, for example) Operation “HA GAIN” “HA GC” “HA HPF” Shows the parameters for “Quick Controls” assigned to the selected channel. The values for each parameter can be changed by dragging on the screen or using the corresponding [Multi function knob]. Function Adjusts the gain. [. . . ] You can also adjust the filter frequency (20 – 600 Hz). To turn on phantom power, press and hold down [Multi function button A]. “HA +48V” MBL-25A MBL-32A MBL-832A MXL-25A MXL-32A MXL-32AF V1. 5 Supplementary Manual 2 Added support for VST instruments control (Nuage Master) You can control VST instruments on instrument tracks on the CHANNEL CONTROL page. 5 W (Write) Turns “Write Automation” on (lit) and off (dark). 6 VST instrument name/library name Shows the selected instrument and library. 7 Parameters Touch a parameter to control it with a [Multi function knob]. Press [Multi function button B] to lock the value for the parameter. Press the button once again to unlock the value. CHANNEL CONTROL – MAIN Page 1 2 3 8 Library Shows the library selection screen. 9 Up/Down Scrolls through the parameters. 1 Instrument Shows the instrument selection screen. Added screen scrolling by dragging (Nuage Master) If a list does not fit on the [Multi Function Display], you can now drag to scroll the screen. When a screen that can be scrolled is displayed, press [CTRL] in the MODIFIER section and an arrow will appear on the screen. Drag in the direction of the arrow to scroll the screen. 2 Ch (Channel) Shows the MIDI channel selection screen. 3 e (Edit) Shows the INST page (see below). CHANNEL CONTROL – INST Page 1 2 3 4 5 6 7 8 9 1 (Nuendo) Opens the “VST Instruments” screen. Click again to close the screen. 2 Return Returns to the MAIN page. 3 On/Off Turns the VST instrument on (lit) and off (dark). 4 R (Read) Turns “Read Automation” on (lit) and off (dark). MBL-25A MBL-32A MBL-832A MXL-25A MXL-32A MXL-32AF V1. 5 Supplementary Manual 3 Added support for track visibility configuration function (Nuage Master) You can now use the “track visibility control” function of Nuendo 6. 5. This can greatly improve work efficiency on large-scale projects. Added support for send panning (Nuage Master) Channel “Sends” can now be panned. CHANNEL CONTROL – SENDS Page 1 2 TRACK LIST Page – Track Visibility View 1 2 3 4 1 LP (Link Panners) Turns “Link Panners” on (lit) and off (dark). 1 Track Visibility Switches to the Track Visibility view. 2 SENDS PAN Shows the SENDS PAN page (see below) for the corresponding slot. 2 Filter Track Types Use filters to select only the track types you want to display. 3 Track Visibility Agents Shows the command list for the track visibility configuration function. CHANNEL CONTROL – SENDS PAN Page 1 2 3 4 5 4 Track Shows (light color) or hides (dark color) tracks. Hidden tracks cannot be operated in the views on the TRACK LIST page. Added super fine mode (Nuage Master, Nuage Fader) Super fine mode allows finer adjustments of the parameters on the CHANNEL STRIP. In some cases, this resulted in wireless LAN being selected. In this version, manual selection has been added so that it is easier to select the Ethernet port on the computer. To select the Ethernet port, on the computer select [System Preferences]  [MBL-25A MBL-32A MBL-832A MXL-25A MXL-32A MXL-32AF PT Bridge]. 4 Refresh Refreshes the direct monitoring channel list. 5 +/- (Show/Hide Channel) Shows (+) or hides (-) the channels assigned to the bus. 6 Number of channels available for direct monitoring Shows the number of channels available for direct monitoring. 7 Direct monitoring channel list Shows the “Bus Name”, “Bus Type”, and “Device Port” of buses selected for direct monitoring. “Bus Type” shows if the channel selected for direct monitoring is assigned to Output or Studio (Control Room). You can remove a bus by selecting it under “Bus Name”, right clicking, and then selecting [Delete] from the context menu. NOTE See the following website for more information and cautions to observe when using direct monitoring. http://www. yamahaproaudio. com/ Network Screen 1 2 1 Configure Set “Network Interface” to either “Automatically” or “Manually”. 2 Network Interface Select the port for connecting MBL-25A MBL-32A MBL-832A MXL-25A MXL-32A MXL-32AF series devices. This option becomes available when “Configure” is set to “Manually”. About Screen Shows the information for MBL-25A MBL-32A MBL-832A MXL-25A MXL-32A MXL-32AF PT Bridge. MBL-25A MBL-32A MBL-832A MXL-25A MXL-32A MXL-32AF V1. 5 Supplementary Manual 6 Added other various functions (Nuage Master) SETUP Page SETUP page is divided into three pages since the number of configurable settings has been increased. PAGE 3 PAGE 1 3 3 MUTE Button Behavior Switches the behavior of [MUTE] on the channel strip. When set to Continuous, pressing and holding [MUTE] on one channel while pressing [MUTE] on another channel will simultaneously turn on and off all “mute” functions for every channel between those two channels. [. . . ] This option becomes available when “Configure” is set to “Manually”. About Screen Shows the information for MBL-25A MBL-32A MBL-832A MXL-25A MXL-32A MXL-32AF PT Bridge. MBL-25A MBL-32A MBL-832A MXL-25A MXL-32A MXL-32AF V1. 5 Supplementary Manual 6 Added other various functions (Nuage Master) SETUP Page SETUP page is divided into three pages since the number of configurable settings has been increased. PAGE 3 PAGE 1 3 3 MUTE Button Behavior Switches the behavior of [MUTE] on the channel strip. When set to Continuous, pressing and holding [MUTE] on one channel while pressing [MUTE] on another channel will simultaneously turn on and off all “mute” functions for every channel between those two channels. When set to Toggle, “mute” is turned on and off only for the channel on which [MUTE] is pressed. PAGE 2 1 2 For the buttons used to adjust the pressing time for Smart Switch Delay, the [TALK BACK] button and other buttons can now be configured separately. [. . . ]