User manual YAMAHA MD4S

[. . . ] MULTITRACK MD RECORDER Owner's Manual IN OUT MIDI THRU TRACK DIRECT OUT 2TR IN STEREO OUT MONITOR OUT 1 2 AUX SEND 1 INSERT I/O 2 MIC/LINE INPUT INSERT 3 I/O LINE INPUT 4 5 6 7 8 GAIN 1 GAIN 2 GAIN 3 GAIN 4 5/6 7/8 LINE MIC/ LINE FLIP CUE MIC PB LINE MIC/ LINE FLIP CUE MIC PB LINE MIC/ LINE FLIP CUE MIC PB LINE MIC/ LINE FLIP CUE MIC PB 0 10 0 10 CH1 CUE MIX TO STEREO P A N 1 BUS L REC SELECT CH2 CH3 CH4 P A N L R L E V E L 0 HIGH 10 HIGH 0 10 L R P A N L L E V E L 0 HIGH 10 R P A N L L E V E L 0 HIGH 10 R 2 3 4 R L R L E V E L MONITOR SELECT 2TR IN MULTITRACK MD RECORDER EJECT PEAK HOLD DISPLAY ­15 MID +15 ­15 MID +15 ­15 MID +15 ­15 MID +15 STEREO PITCH ADJUST EDIT UTILITY ­15 LOW +15 ­15 LOW +15 ­15 LOW +15 ­15 LOW +15 CUE EXIT ­15 AUX +15 ­15 AUX +15 ­15 AUX +15 ­15 AUX +15 ENTER 1 PAN 2 PAN 1 2 PAN 1 2 PAN 1 2 MONITOR LEVEL REPEAT L 10 9 8 7 6 5 4 3 2 1 0 R 10 9 8 7 6 5 4 3 2 1 0 L R 10 9 8 7 6 5 4 3 2 1 0 L R 10 9 8 7 6 5 4 3 2 1 0 L R 10 9 8 7 6 5 4 3 2 1 0 MIN MAX MARK SEARCH MARK 10 9 8 7 6 5 4 3 2 1 0 A B LAST REC SEARCH IN OUT SET AUTO PUNCH I/O SONG SEARCH PAUSE REHE REC PLAY STOP DATA CURSOR TOC WRITE 1 2 3 4 STEREO PHONES PUNCH I/O E FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. [. . . ] At this time, there will be a volume difference between the first 1. 5 seconds and the last 1. 5 seconds, so that you can hear exactly where the marker occurs. 4. Press the PLAY button, and while listening to playback 1. 5 seconds before and after the marker, rotate the DATA dial to adjust the location of the marker in single-frame units (11. 6 ms). When you rotate the DATA dial to move the marker backward or forward, the display will indicate "ADJST XXX " (XXX is the number of frames that the marker was moved. ) 5. As necessary, rotate the CURSOR shuttle to invert the high/low volume change. By rotating the CURSOR shuttle to left or right you can invert the high/low volume change that occurs between the first 1. 5 seconds and the last 1. 5 seconds. If the display indicates , the first 1. 5 seconds will be played at a lower volume. if the display indicates , the last 1. 5 seconds will be played at a lower volume. CURSOR shuttle Display Playback volume 1. 5 sec. 1. 5 sec. Marker or auto punch-in/out point Marker or auto punch-in/out point Tip: 1. 5 seconds before and after the marker will also playback immediately after you rotate the CURSOR shuttle. If you keep inverting the volume difference while you listen, it will be easier to make accurate adjustments to the position. 6. When you have finished making adjustments, press the ENTER button. The new location will be finalized, and the MD4S will locate to that spot. The display will return to the state in which it was before you press the ADJUST button in step 2. 7. Press the ADJUST button once again to return to normal operation. Press the TOC WRITE button to update the TOC. Note: The frames with which we are dealing here are 11. 6 ms units. If MTC frames are displayed in the time display, the adjusted location may not be reflected by the time counter. --Owner's Manual Quick search functions 65 Note: This method can be used to make fine adjustments in a range of approximately 10 seconds forward or backward from the selected marker (or auto punch-in/out point). If you wish to make adjustments that would be further than this range, you will need to either repeat steps 2­6, or re-set the point that you wish to adjust. If another marker has already been inserted before or after the marker (or auto punch-in/out point) that you are moving, it is not possible to move these markers past each other. Erasing a marker or auto punch-in/out point Here's how to erase a marker location or auto punch-in/out point that you have set. This procedure can be performed when the MD4S is either stopped or in playback-pause mode. 1. Press a MARK SEARCH or LAST REC SEARCH button to locate to the marker or the auto punch-in/out point that you wish to erase. Press the ADJUST button. The display will indicate "MARK X:ADJST" or "IN:ADJST" or "OUT:ADJST, " and the word on the left (MARK X/IN/OUT) will blink. At this time, you may rotate the DATA dial to select a different marker or auto punch-in/out point. 3. Rotate the CURSOR shuttle toward the right. The word "ADJST" in the display will blink. 4. Rotate the DATA dial toward the right. The word "ADJST" in the display will change to "CLEAR. " 5. Press the ENTER button. If you are erasing a marker, the display will indicate "CLR MARKX?" (X will be the marker number). By pressing the EXIT button at this point you can cancel the Erase operation. 6. [. . . ] See "Setting the pre-roll/post-roll times" on page 55 for more information. Punch In/Out--A recording technique that allows you to rerecord specific sections of an existing track. The MD4S provides both manual and automatic punch in/out operations. Random Access--The ability to access data instantly. [. . . ]