User manual YAMAHA MG24 14FX

[. . . ] MIXING CONSOLE Owner's Manual MG32/14 FX MG24/14 FX E Important Notice ­ connecting a lamp ­ Please read carefully before connecting a lamp to the LAMP Jack. (page 18) · Do not use a lamp that grounds Pin 2 or Pin 3 to the shell (body). Use of the wrong lamp type may result in damage to the mixer. Recommended lamps: Littlite's X-HI series of gooseneck lamps. [. . . ] On stereo channels, the L (odd) and R (even) input signals are mixed before moving into the EFFECT bus. NOTE These knobs operate as EFFECT controls only if the AUX5/AUX6 switch is in off position ( ). If the switch is on, these knobs adjust the output to the AUX5 and AUX6 buses. (See 8 below. ) Lights up when the channel's post-equalizer signal level comes within 3 dB of the clipping level. C SIGNAL indicator Lights up when a signal is being input into the channel. D GROUP Switches Use these switches to feed the channel's signal to the GROUP 1-2 and/or GROUP 3-4 buses. Setting the switch on ( ) causes the signal to feed into the corresponding GROUP buses. NOTE These switches allow you to independently assign the signal to groups regardless of the setting of the ST switch (E). 8 AUX5, AUX6 Switch Selects whether the channel signal is sent to AUX buses 5 and 6 or EFFECT buses l and 2. If the switch is on ( ), the signal goes to AUX5 and 6 buses; if off ( ), the signal goes to the EFFECT buses. Note that the signal to these buses is always post-fader. E ST Switch Set this switch on ( bus. ) to feed the channel's signal to the ST F Channel Fader Adjusts the output level of the channel's signal. Use these faders to adjust the volume balance among the various channels. NOTE To reduce noise, set the fader sliders for unused channels all the way down. 9 PAN Control (Monaural Channels) BAL Control (Stereo Channels) The PAN control adjusts the signal's pan positioning into the Group 1-2 bus pair, into the Group 3-4 bus pair, and into the Stereo bus's L and R lines. The BAL control knob sets the balance between left and right channels. Signals into the L input (odd channel) feed to the Group 1 and Group 3 buses and to the L line of the Stereo bus. Signals into the R input (even channel) feed to the Group 2 and Group 4 buses and to the R line of the Stereo bus. NOTE If you are inputting to a stereo channel through the L (MONO) jack only, the BAL knob operates as a PAN knob. MG32/14FX, MG24/14FX 11 Front & Rear Panels G PHANTOM +48 V Switch Toggles phantom power on or off to a set of eight adjacent channels. The MG32/14FX has three of these switches: for CHs 1 to 8, for CHs 9 to 16, and for CHs 17 to 24. The MG24/14FX has two: for CHs 1 to 8 and for CHs 9 to16. If using condenser microphones, set the switch on ( ) for all channels to which these microphones are connected. NOTE If this switch is on ( ), the mixer supplies DC +48 V power to pins 2 and 3 of all XLR-type jacks in the corresponding channels. · Be sure to leave these switches off ( ) if you do not need phantom power. Humming or damage may result if you connect to an unbalanced device or to an ungrounded transformer while this switch is on ( ). But note that the switch may be left on without problem when connecting to balanced dynamic microphones. · To avoid damage to speakers, be sure to turn off amplifiers (or powered speakers) before turning these switches on or off. Monaural channels Stereo channels 12 MG32/14FX, MG24/14FX Front & Rear Panels Master Control Block I STEREO/MONO Section You use this section to independently adjust the levels of the outputs from the ST bus. You can independently adjust the main stereo output, the sub stereo output, and the mixed monaural output. 5 LPF (MONO) · LPF Switch Set this switch ON to apply a low-pass filter to the signal output from the MONO output jack, or OFF to turn this LPF off. If the switch is ON, the LPF will cut frequencies that are above the cutoff set by the Frequency Adjustment dial. · Frequency Adjustment Dial Adjusts the cutoff frequency for the LPF. The adjustment range is 80 Hz to 120 Hz. [. . . ] Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 BELGIUM/LUXEMBOURG Yamaha Music Central Europe GmbH, Branch Belgium Rue de Geneve (Genevastraat) 10, 1140 - Brussels, Belgium Tel: 02-726 6032 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. 25/F. , United Plaza, 1468 Nanjing Road (West), Jingan, Shanghai, China Tel: 021-6247-2211 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. [. . . ]