User manual YAMAHA MLC-16

[. . . ] Contact your Yamaha dealer or service center for this type of upgrade. · DME Designer cannot be used to downgrade DME firmware version 3. 8 or later to version 3. 5 or earlier (this does not apply to the SP2060 or ICP1). Contact your Yamaha dealer or service center for this type of downgrade. · DME firmware versions 3. 8 or later cannot be written using DME Designer version 3. 5 or earlier. [. . . ] All DME devices in the same Device Group must be set to the same network address. n When only one DME unit (Master) is used, the IP address should be set to "192. 168. 0. 2". n The subnet mask is fixed at "255. 255. 255. 0". n The host address can be set from 2 to 253 for the Master device, and from 3 to 253 for Slaves. n Always use a private address (192. 168. 0. 2. through 192. 168. 255. 253) unless it is absolutely necessary to use a global address. Consult with the network administrator if it is necessary to use a global address. 3 Press and hold the [UTILITY] button for at least 2 seconds to display the Utility screen. Network address Host address Master ID When a device is assigned as a Slave in Master/ Slave ( ) above, this sets the host address for the Master device in that group. This parameter cannot be set for the Master device. 4 Press the [UTILITY] button several times until the Net page appears. Link Mode Ensure that "100Base-TX" is selected for this parameter. 6 Press the [HOME] button to return and save your changes. 5 Use the [ ] and [ ] buttons to move the cursor to the parameters listed below and press the [ENTER] button. The corresponding editing dialog will appear. Set each of the following parameters as described and press the [ENTER] button each time to confirm and enter the settings. Master/Slave This parameter sets device-group master or slave status. One DME unit must be assigned as the master in each device group. All other DME units in the group should be set to slave. DME Setup Manual 21 In-depth Information on DME Units Related web site on DME series and peripherals The latest information about DME units is available from the Yamaha Pro Audio website: http://www. yamahaproaudio. com The latest version of the DME unit firmware and DME Designer can be downloaded from the Yamaha ProAudio website: http://www. yamahaproaudio. com/downloads/firm_soft/index. html Library data for DME series Speaker Processor Components and DME remote control protocol specifications is available from the "Downloads" page of the Yamaha Pro Audio website: http://www. yamahaproaudio. com/downloads/documents/index. html For information on touch panel controllers by other manufacturers, visit: AMX's web site: http://www. amx. com/ CRESTRON's web site: http://www. crestron. com/ DME Setup Manual 22 DME-N Network Driver Setup Details "DME-N Network Driver" dialog box Select [Start] [Control Panel] [DME-N Network Driver] to open the "DME-N Network Driver" dialog box. The parameters in this dialog box set up the device information of the DME on the network. [Remove] Button Deletes the selected device from the list. Also, devices added to the Target Device List ( ) by pressing the [New] or [Duplicate] buttons will only actually be registered for communication with the DME-N Network Driver when the [Apply] button is pressed. [Advanced Settings] Button Opens the "Advanced Settings" window. This window provides access to advanced settings. For details refer to the "Advanced Settings" dialog box in the next section. DME Setup Manual 24 DME-N Network Driver Setup Details "Advanced Settings" dialog box Click [Advanced Settings] in the DME-N Network Driver dialog box to display the Advanced Settings dialog box. The parameters presented in this dialog box are used to setup automatic detection by the DME-N Network Driver; furthermore, setup files can also be imported and exported here. Detected Device List This list shows all detected devices that are capable of communication with the DME-N Network Driver. [Add] Checked devices will be added to the Target Device List when the [Add to Device List] button (below) is clicked. Devices that are already registered cannot be checked. [Device IP Address] The IP address of the corresponding detected device. [Device Name] If a name has been registered for the detected device it will be displayed here, otherwise no name will be displayed. Device MAC Address The MAC address of the corresponding detected device. [Add to Device List] Button Devices with checked [Add] checkboxes will be added to the Target Device List when this button is clicked. [. . . ] When a new file is created using DME Designer, the word clock is set to "INT48k" by default. In systems where the DME unit operates as a word-clock slave, it will be necessary to change this word-clock setting before going online. If the DME unit were to be brought online with the default setting unchanged, it would not be word-clock locked with the other units in the system, resulting in audible clicking and possibly damage to the other units. Whenever possible, it is recommended that clock settings be made using DME Designer. [. . . ]