User manual YAMAHA MU128

[. . . ] English Deutsch Français TONE GENERATOR PLAY EDIT MUTE/ SOLO ALL PART PART UTIL EFFECT 1 A/D INPUT XG TG300B PERFORM ENTER SELECT SELECT MODE EQ EXIT VALUE VALUE 2 VOLUME Piano PART BANK/PGM VOL EXP PAN REV CHO VAR KEY Chrom. perc. Organ Guitar Bass Strings Ensemble Brass Reed Pipe Synth lead Synth pad SELECT PART GROUP STAND BY ON Synth effects Ethnic Percussive SFX Model excl. Drum MIDI IN A PHONES MU PLG-1 PLG-2 PLG-3 FCC INFORMATION (U. S. A) 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. [. . . ] For example, you may want to have a Symphonic effect on one Voice and Phaser on another. Variation also gives you many special effects not found in the Reverb and Chorus sections, such as Delay, Gate Reverb, Wah and Pitch Change. The Variation effect can be applied either to all Parts (as with Reverb and Chorus), or to a single selected Part (as described below). Operation 1 Set Variation Connection to "INS" (Insertion). To use Variation with a single Part, the Variation Connection parameter should be set to Insertion. To do this: 1) Press the [EFFECT] button. 2) Select "VAR" (with the [SELECT </>] buttons) and press [ENTER]. 3) Select "VarConnect" (with the [SELECT >] button), and change the setting to "INS" (with the [VALUE -/+] buttons or data dial). 2 Select the desired Part and set its Variation Send control to "on. " To do this: 1) Return to the Multi Play mode Single Part display (press the [PLAY] button), then select the desired Part (with the [PART -/+] buttons). 2) Select "VarSend" (with the [SELECT </>] buttons), and set it to "on" (with the [VALUE-/+] buttons or data dial). 3 Return to the Variation parameters, select the Distortion Type, and make other necessary settings. To do this: 1) Press the [EFFECT] button. 2) Select "VAR" (with the [SELECT -/+] buttons) and press [ENTER]. 3) Select "Type" (with the [SELECT <] button), and change the setting to "DISTORTION" (with the [VALUE -/+] buttons or data dial). 90 MU128 Guided Tour Effects 4) If you cannot hear the Distortion effect clearly, select the "Dry/Wet" parameter (with the [SELECT </>] buttons) and adjust it (with the [VALUE -/+] buttons or data dial) until the sound is appropriate. 5) Using the same method (as in step #4), select and adjust other important Distortion parameters as needed, such as "Drive" and "OutputLvl" (Output Level). Now, play the Part and hear how Distortion affects the sound. Select other Types and play with them as well. The Variation parameters differ depending on the selected Variation Type. For a list of Variation Types and other information on Variation, see page 149. For a list of the available parameters for each Variation Type, refer to the "Sound List & MIDI Data" booklet. English Details · When Variation is set for use with a single Part (Insertion), only Variation Send is available. (The Dry/Wet parameter in Variation Edit effectively performs the same function as Variation Return in this case; see page 150. ) Also, Variation Send can be set to "on" for only one Part. · When Variation is set for use with all Parts (System), both Variation Send and Return must be set to appropriate values. [. . . ] Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-703-0900 SWEDEN Yamaha Scandinavia AB J. Wettergrens Gata 1 Box 30053 S-400 43 Göteborg, Sweden Tel: 031 89 34 00 BRAZIL Yamaha Musical do Brasil LTDA. Rebouças 2636, São Paulo, Brasil Tel: 011-853-1377 PHILIPPINES Yupangco Music Corporation 339 Gil J. Box 885 MCPO, Makati, Metro Manila, Philippines Tel: 819-7551 DENMARK YS Copenhagen Liaison Office Generatorvej 8B DK-2730 Herlev, Denmark Tel: 44 92 49 00 ARGENTINA Yamaha Music Argentina S. A. [. . . ]