User manual YAMAHA MX-50

[. . . ] The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 12 13 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. 14 1 2 3 4 5 Read Instructions ­ All the safety and operating instructions should be read before the product is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. Heed Warnings ­ All warnings on the product and in the operating instructions should be adhered to. [. . . ] Table of Program Names for Each Input Format Input 2 channel Stereo No. 9 Program MOVIE THEATER 1 70 mm Spectacle 70 mm Sci-Fi 10 MOVIE THEATER 2 70 mm Adventure 70 mm General 11 DOLBY DIGITAL -- -- DTS DIGITAL SUR -- DGTL Spectacle DGTL Sci-Fi DGTL Adventure DGTL General Normal Enhanced -- DTS Spectacle DTS Sci-Fi DTS Adventure DTS General -- -- Normal Spectacle 6. 1 Sci-Fi 6. 1 Adventure 6. 1 General 6. 1 Matrix 6. 1 Enhanced 6. 1 -- Spectacle ES Sci-Fi ES Adventure ES General ES -- -- ES Matrix 6. 1 ES Discrete 6. 1 *2 Enhanced ES -- -- -- -- -- -- 5. 1 channel DOLBY DIGITAL DTS 6. 1 channel *1 DOLBY DIGITAL DTS ES INTRODUCTION PREPARATION BASIC OPERATION -- PRO LOGIC Normal Enhanced PRO LOGIC Movie Music DTS Neo: 6 Cinema Music -- -- -- -- -- -- -- Enhanced -- -- -- -- -- -- -- -- -- -- -- -- -- ADVANCED OPERATION ADDITIONAL INFORMATION *1 means the 6. 1/ES decoder is ON. *2 means the DTS ES software encoded with Discrete 6. 1 is input. y · If a Dolby Digital signal or DTS signal is input when the input mode is set to AUTO, the DSP program will be automatically switched to the Dolby Digital playback sound field or DTS playback sound field. · If Dolby Digital Surround EX software or DTS ES software is played when AUTO is selected by pressing the 6. 1/ES button on the remote control, the Dolby Digital Matrix 6. 1 or DTS ES decoder usually turns on and the corresponding DSP program is selected. · 6. 1/ES on the remote control can be used to play Dolby Digital or DTS 5. 1 channel sources with rear center speaker. In this case the program name changes to the corresponding name for 6. 1 channel. · When playing 6. 1 channel source with 6. 1/ES on the remote control off, the program name changes to the corresponding name for 5. 1 channel. APPENDIX Note · The " " indicator does not light up when selecting the program No. 11 except for the Enhanced mode. English 35 CINEMA-DSP The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital recreations of actual acoustic environments. Note · Select the DSP program that you feel sounds best regardless of the name and description given for it below. 9 Program MOVIE THEATER 1 Spectacle Features This program creates the extremely wide sound field of a 70-mm movie theater. It precisely reproduces the source sound in detail, making both the video and the sound field incredibly real. North, Central and South America: 100 kHz/10 kHz Other area: 50 kHz/9 kHz Before setting this switch, disconnect the AC power plug of this unit from the AC outlet. 100kHz/10kHz INTRODUCTION I Connecting the AM loop antenna 1 Set up the AM loop antenna, then connect it. PREPARATION 50kHz/9kHz FREQUENCY STEP 2 Press and hold the tab to insert the AM loop antenna lead wires into the AM ANT and GND terminals. BASIC OPERATION AM loop antenna (included) Indoor FM antenna (included) (U. S. A. model) 3 COMPONENT VIDEO PR/CR PB/CB Y Orient the AM loop antenna for the beat reception. ADVANCED OPERATION A DVD B D-TV /LD MONITOR OUT TUNER AM ANT GND y 75 UNBAL. FM ANT · The AM loop antenna can be removed from the stand and attached to a wall, etc. ADDITIONAL INFORMATION Notes Ground (GND terminal) For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. · The AM loop antenna should be placed away from this unit. · The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit. A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas. APPENDIX I Connecting the indoor FM antenna Connect the included indoor FM antenna to the 75 UNBAL. FM ANT terminal. English 37 TUNING Automatic and Manual Tuning There are 2 ways of tuning; automatic and manual. Automatic tuning is effective when station signals are strong and there is no interference. 4 Press PRESET/TUNING l / h once to begin automatic tuning. Press h to tune in to a higher frequency, or press l to tune in to a lower frequency. PRESET/ TUNING VCR 1 CBL/SAT D TV/LD DVD MD/TAPE CD R TUNER TUNED CD AUTO I Automatic tuning 1 INPUT INPUT MODE SP A A AM 1440 VOLUME NATURAL SOUND AV RECEIVER D I G I TA L When tuned in to a station, the "TUNED" indicator lights up and the frequency of the received station is shown on the front panel display. STANDBY /ON y SPEAKERS A B SOURCE /REMOTE MD/TAPE DVD CD-R TUNER CD PHONO A/B/C/D/E PRESET/ TUNING PRESET /TUNING FM/AM MEMORY TUNING MODE SILENT D-TV/LD CBL/SAT VCR1 EDIT MAN'L/AUTO FM S VIDEO AUTO/MAN'L MONO VIDEO L AUDIO R OPTICAL BASS PROCESSOR EXTENSION DIRECT PHONES VCR2 /DVR STEREO PROGRAM 6CH INPUT · Use the manual tuning method if the tuning search does not stop at the desired station because the signal is weak. V-AUX ­ BASS + ­ TREBLE + EFFECT REC OUT/ZONE 2 VIDEO AUX I Manual tuning If the signal from the station you want to select is weak, you must tune in to it manually. 4 32 3 1 2 1 Press INPUT l / h (TUNER on the remote control) to select TUNER as the input source. INPUT PHONO Select TUNER and the reception band following steps 1 and 2 described in "Automatic tuning" on left. Press TUNING MODE (AUTO/MAN'L MONO) so that the "AUTO" indicator goes off from the front panel display. TUNING MODE or V-AUX TUNER MD/TAPE CD-R CD D-TV/LD CBL/SAT VCR 1 VCR2/DVR DVD AUTO Front panel Remote control AUTO/MAN'L MONO Goes off 2 Press FM/AM to select the reception band. "FM" or "AM" appears on the front panel display. FM/AM If the colon (:) appears on the front panel display next to the band indication, press PRESET/TUNING EDIT to turn it off. PRESET /TUNING VCR 1 CBL/SAT D TV/LD DVD MD/TAPE CD R TUNER TUNED or CD 3 EDIT Press TUNING MODE (AUTO/MAN'L MONO) so that the "AUTO" indicator lights up on the front panel display. TUNING MODE SP A A AM 1440 3 AUTO/MAN'L MONO AUTO Lights up Press PRESET/TUNING l / h to tune in to the desired station manually. [. . . ] and Canada models] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 W/640 VA [Other models] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 W Standby Mode [U. S. A. , Canada, and Australia models] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 2 W [China and General models] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]