User manual YAMAHA NCX900R

[. . . ] Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. [. . . ] · If there is any track that cannot be copied digitally among the tracks to be combined, the combined track cannot be copied digitally either. · When tracks with different emphasis status have been combined, the emphasis status of the first track becomes effective for the combined track. 001 1L dB ­30 ­10 ­6 2 TRACK ­2 0 R Track to be the first in the combination Track to be the last in the combination Press CLEAR to cancel the confirmed selection. English E-45 TRACK EDITING Track Divide You can divide a track into two at the selected point. 6. Set the dividing point by rotating the MULTI JOG knob (pressing +/­ on the remote control). The dividing point can be set by "minute: second: frame". Move the flash to the unit to be set by pressing t/e or r/y. If you stop rotating the MULTI JOG knob, this unit searches for the dividing point according to the setting made, and starts repeated playback of the passage between the dividing point and the point that is 5 seconds after the dividing point. Dividing point Track GROUP I Editing during the stop mode 1. Select and confirm "Track Divide" in step 5 of "Editing during the stop mode" on page 39. The following message appears on the display. Disc that contains the track to be divided Divide 001 1? L dB ­30 ­10 ­6 ­2 0 R Passage to be repeatedly played Track to be divided 7. Press COMPLETE. The selected track is divided into two at the set dividing point. This unit returns to the editing menu item selection. The disc number that contains the track to be divided flashes. 2. Select the disc that contains the track to be divided by rotating the MULTI JOG knob (pressing +/­ on the remote control). I Editing during playback 3. However, if there is any unused track number, only the tracks up to that number will be up-numbered. Before "Track Divide" is performed Track Pack You can re-organize the track numbers by eliminating unused track numbers, that have been created by changing track numbers or erasing tracks. 1. Select and confirm "Track Pack" in step 5 of "Editing during the stop mode" on page 39. The following message appears on the display. Pack 001 L dB ­30 ­10 ­6 ­2 ? 0 EDITING R Disc on which unused track numbers are to be eliminated 2. Select the disc on which unused track numbers are to be eliminated by rotating the MULTI JOG knob (pressing +/­ on the remote control). 1 2 4 5 6 3. Press the MULTI JOG knob (ENTER on the remote Divided into two control) to confirm the disc on which unused track numbers are to be eliminated. 3 4 5 6 1 2 Press CLEAR to cancel the confirmed selection. After "Track Divide" has been performed (dividing a track into two) : Space not being used 4. Press COMPLETE. The track numbers are re-organized by eliminating unused track numbers. This unit returns to the editing menu item selection. Before "Track Pack" is performed 1 3 4 6 1 2 3 4 5 6 After "Track Pack" has been performed (Unused track numbers have been eliminated. ) : Unused track numbers English E-47 TRACK EDITING Add Fade In You can add fade-in at the beginning of a track. The beginning of the track is played with gradually rising level when fade-in has been added. 6. Rotate MULTI JOG knob (+/­ on the remote control) to set the fade-in length. The fade-in length can be set in the 1 to 10 second range by 1second steps. If you stop rotating the MULTI JOG knob, this unit starts repeated playback of the beginning of the track with a fade-in of the length set in above step, with extra portion for further 5 seconds. [. . . ] · Disconnect all the connections. · Set the HDD to SLAVE (see description below). MASTER or SLAVE setting on the HDD It is necessary to set the HDD to MASTER or SLAVE when connecting the HDD to the component you plan to use. This unit is designed to operate HDD when it is set to SLAVE. [. . . ]