User manual YAMAHA NUAGE FADER GETTING STARTED

[. . . ] NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. [. . . ] WARNING Only use the included power cable (or an equivalent recommended by Yamaha). Using the wrong cable can result in damage to the device or overheating. CAUTION Remove the plug of the power cable from the outlet when the device is not be used for extended periods of time, or during electrical storms. NUAGE I/O (16D )/ NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual 11 Description of the Device Description of the Device Front Panel NUAGE I/O (16D) 1 2 4 3 5 6 NUAGE I/O (16A) 1 2 3 5 6 NUAGE I/O (8A8D) 1 2 4 3 5 6 12 NUAGE I/O (16D) / NUAGE I/O (16A) / NUAGE I/O (8A8D) Operation Manual Description of the Device 1 [INPUT level meter] 4 [SRC indicator] Indicates the input signal level of [ANALOG INPUT] (page 16) or [AES/EBU] (page 16) on the rear panel. Lamp Top (red) Second (orange) Third (orange) Bottom (green) Indicates the status of the SRC (sample rate converter), on (lit) or off (unlit). When you turn SRC on, even if the sample rate at which the device is operating differs from the sample rate of the audio signal input to the device, the SRC function automatically converts the rate of the signal so that playback will be correct. sRC is available on every two adjacent channels. To turn SRC on/off, use the NUAGE Workgroup Manager (page 19). 5 [OUTPUT level meter] Lighting level 0 dBFS -3 dBFS or more -14 dBFS or more -48 dBFS or more 2 [SAMPLE RATE indicator] Indicates the sample rate of the device. To select the sample rate of the device, use the NUAGE Workgroup Manager (page 19). 3 [CLOCK indicator] Indicates the output signal level of [ANALOG OUTPUT] (page 16) or [AES/EBU] (page 16) on the rear panel. When connecting multiple devices, set the ID on each device to a different number. Note that you can only select the device ID while the power is off. If you change this while the power is on, the new device ID will not be applied. 4 [Dip switch] For connection to the BNC coaxial cable. When connecting this connector to NUENDO SyncStation, Nuendo and the devices maintain accurate synchronization with each other. 8 [WORDCLOCK OUT] (BNC connector) Sets the device settings or initializes them. Note that you can only select [Dip switch] while the power is off. If you change this while the power is on, the settings will not be applied. [Dip switch] Description 1 Selects whether [SECONDARY] (page 15) will operate as a redundant network (page 9) or daisy chain connection (page 9). [SECONDARY] will operate as a redundant network when you turn this on (down), and daisy chain connection when you turn this off (up). Turn the power of the device on, then wait for the [OUTPUT level meter] of the 16 channels to flash at intervals. [. . . ] This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc. , 51 Franklin Street , Fifth Floor , Boston , MA 02110-1301 , USA. [. . . ]