User manual YAMAHA PDM-4210

[. . . ] G PDM-4210E High definition plasma monitor Moniteur plasma haute définition USER'S MANUAL MANUEL UTILISATEUR BEDIENUNGSANLEITUNG BRUKSANVISNING MANUAL DE USUARIO ENGLISH USER'S MANUAL Thank you very much for purchasing the Yamaha High Definition Plasma Monitor. Before using your monitor, please carefully read this manual so you will know how to operate the monitor properly. You will find it useful in the future. Notes on lnstallation Work: This product is marketed assuming that it is installed by qualifed personnel with enough skill and competence. Always have an installation specialist or your dealer install and set up the product. [. . . ] b] The image retention images in this document are exaggerated for the purpose of explanation. The actual manner in which the image retention Methods to Reduce the Occurrence of Image Retention · Lower the Contrast and Brightness settings of the plasma display panel as much as possible. A function is provided in the display that allows you to control the brightness of the screen to reduce degradation of the panel. Using this function makes it possible to reduce image retention. (Refer to Panel Life (Extend 1. or Extend 2 shown on 19 ) · Set the plasma monitor to an "Screen Wipe" or "Inverse" display. The occurrence of image retention when displaying images of identical patterns, such as static images, for long periods of time can be reduced by displaying a reversed colour or completely white screen for about 1 ~ 2 hours after terminating the display. (Settings can be made using Screen Wipe and Inverse of Function MENU shown on 19 ) · Using in combination with moving images Since the degradation of the fluorescent material progresses comparatively uniformly for moving images, the occurrence of partial image retention can be controlled. We recommend using the plasma monitor in combination with moving images such as those of DVD. * Please be careful since image retention will occur if display is left in a two screen display state for a long period of time. * Television broadcasts include images displayed for long periods of time in which the left and right or top and bottom of the image are cut and broadcast station name or time are displayed for a long period of time at the same portion of the screen. Image retention in these portions can be expected to occur, so please be aware. NOTES About screen defects · High precision technology is used in the making of plasma display panel but there may be dark spots (points that do not illuminate) and bright spots (points that are too bright) in some cases. These do not indicate a malfunction. About residual images · In some cases, residual images may remain after the short-term display of still images and another image is displayed, but these will disappear and return to normalcy. This is not a malfunction. About the panel screen · Plasma display panels display images by means of electrical discharges inside the panel. Because of this, the temperature of the panel surface may rise in some cases. Also, plasma display panels are made of finely processed glass. A reinforced glass filter is installed over the panel surface but avoid strong impact because there is still danger of glass breakage. 23 TROUBLESHOOTING Symptoms That Appear to be Failures Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer. CAUTION Customer servicing can be hazardous. Symptom · No picture with the power-indicating lamp off. Signal" or "Power Save" is displayed. · No picture, with the power indicating lamp lit orange. Point to check · Check the way the power cable is connected. · Check the way the signal cable is connected. · Make sure that the switch of the computer, imaging equipment , etc. , is turned on. · Make sure the computer is not in the power-save mode. · Check to see if the input selection matches the connection terminal. [. . . ] · If the sound signal has hiss noise or the plasma monitor keeps switching between stereo and mono mode due to signal condition, press the CH I / II button until M appears on the screen to receive a clear mono sound. 53 OPERATING INSTRUCTIONS (continued) OTHER FUNCTIONS (continued) DVD Player Selection · You can use this remote control to operate various, brands of DVD player by pressing the following buttons on the remote control simultaneously. YAMAHA Press RECALL 3 or RECALL 5 Other brands Brands of DVD Player Hitachi Pioneer Panasonic Toshiba Philips JVC Samsung Sony Press Brands of DVD Player Press RECALL RECALL RECALL RECALL RECALL RECALL RECALL RECALL 1 2 3 4 5 6 7 8 RCA Mitsubishi Onkyo Zenith Orion Shinco Skyworth Bubuko RECALL RECALL RECALL RECALL RECALL RECALL RECALL RECALL 9 0 INDEX MODE SUB PAGE CANCEL REVEAL TV/TEXT Example To operate a YAMAHA DVD player, press and hold the RECALL button, followed by the 3 or 5 button. D/N i+ I / II MENU A/B 2-4-12 RECALL button OK P+ + PDVD FREEZE ZOOM 1 2 5 8 0 3 6 9 MODE button 4 7 SUB PAGE buttons AV1 AV2 AV3 AV4 INDEX button RGB1 RGB2 TV / TEXT button CANCEL button REVEAL button NOTE · Not all models of the listed brands can be operated using this remote control. 54 TROUBLESHOOTING Symptoms That Seemingly Appear to be Failures Make the checks suggested below depending on the symptoms observed. If the symptoms persist, contact your dealer. ENGLISH CAUTION Customer servicing can be hazardous. Symptom Possible reason (1) Connection of antenna cable to the TV is poor. (2) Corroded or poor antenna connections. [. . . ]