User manual YAMAHA PM-200B

[. . . ] Do not attempt to play the disc on an audio CD player. Doing so may result in irreparable damage to your audio CD player. · The screen displays as illustrated in this owner's manual are for instructional purposes, and may appear somewhat different from the screens which appear on your computer. · Future upgrades of application and system software and any changes in specifications and functions will be announced separately. [. . . ] This is linked with the encoder of each channel if PAN is selected as the encoder mode, and with the [PAN] encoder of the SELECTED CHANNEL section. F LCR J Turns LCR mode on/off for each channel. If this is turned on for a channel, you can use the TO ST PAN (5) knob to simultaneously control the level of the signal sent to the STEREO bus L/R channels and CENTER channel. G CSR (Center Side Ratio) This adjusts the level ratio (0­100%) of the CENTER channel relative to the STEREO bus L/R channels. To change the value, drag upward or downward inside the numerical box. H ON Switches the input channel on/off. This is linked with the INPUT channel strip CH [ON] keys on the PM5D panel. I Fader Adjusts the input level of the input channel. This is linked with the INPUT channel strip faders on the PM5D panel. The current value is shown in the numerical box immediately below. J CUE This button cue-monitors the signal of the input channel. This is linked with the INPUT channel strip [CUE] keys on the PM5D panel. 27 PM5D Editor Owner's Manual CH to MIX (Channel to mix) 2 1 3 4 5 A MIX send level This adjusts the send level of the signal sent from the input channel to VARI-type MIX buses. The current value is shown in the numerical box immediately above. B Pair This indicates the pairing status of adjacent odd-numbered/even-numbered MIX channels. You can click the heart symbol to enable/disable pairing. C ON (MIX send on/off) This is an on/off switch for the signal sent from the input channel to the MIX bus. D PRE (Pre/Post) This selects PRE or POST as the point from which the signal is sent from the input channel to the MIX bus. E CH to MIX PRE POINT This selects PRE EQ or PRE FADER as the point from which the signal is sent when the PRE button (4) is set to PRE. NOTE If the PRE button is set to POST, you can select either POST ON or POST TO ST as the signal send location individually for each MIX bus ( p. 33). 28 PM5D Editor Owner's Manual If a MIX channel is selected CHANNEL SELECT (Channel selection) Except for the fact that your editing applies to a MIX channel, this is the same as for an input channel ( p. 20). COMPRESSOR Except for the fact that the COMP LINK GROUP is A­F, and that the types of signal that can be selected for keyin are different, this is the same as for the compressor of an input channel ( p. 23). INSERT Except for the fact that the insert points that can be selected are different, this is the same as for the insert settings of an input channel ( p. 24). 29 PM5D Editor Owner's Manual EQUALIZER 2 1 7 6 3 9 8 4 5 K J L M A EQ graph N Indicates the approximate response for the EQ of the currently selected channel. B FLAT If you click this button, the gain of all bands will be reset to 0. 00 dB. CQ D F (Frequency) E GAIN These knobs adjust the Q, center frequency, and boost/cut amount for each band. F (LOW shelving) If this button is on, the LOW EQ will be switched to a shelving type (the Q knob of the LOW EQ will disappear). G HPF (High Pass Filter) If this button is on, the LOW EQ will function as a high pass filter EQ. The Q knob of the LOW EQ will disappear, and the GAIN knob will act as the high pass filter on/off switch. H (HIGH shelving) If this button is on, the HIGH EQ will be switched to a shelving type (the Q knob of the HIGH EQ will disappear). I LPF (Low Pass Filter) If this button is on, the HIGH EQ will function as a low pass filter. The Q knob of the HIGH EQ will disappear, and the GAIN knob will act as the low pass filter on/off switch. J ON (On/off) Switches the EQ on/off. K LIBRARY Accesses the OUTPUT EQ page of the LIBRARY window. 30 PM5D Editor Owner's Manual L TYPE I/TYPE II (EQ type) Selects either TYPE I (an algorithm equivalent to the EQ in the earlier 02R series) or TYPE II (a newly developed algorithm) as the EQ type. M EQ LINK GROUP Selects the EQ link group (A­F) to which that channel belongs. N UPPER/LOWER Switches the four bands affected by controls 3­9 between LOWER (1 LOW­4 HIGH) and UPPER (5 LOW­8 HIGH). DELAY This is the same as for the delay settings of an input channel ( p. 26). DCA GROUP / MUTE GROUP / SAFE 1 2 3 A DCA GROUP Selects the DCA group (7/8) to which the MIX channel belongs. B MUTE GROUP Selects the mute group (1­8) to which the MIX channel belongs. C RECALL SAFE / MUTE SAFE These enable/disable Recall Safe and Mute Safe for the MIX channel. 31 PM5D Editor Owner's Manual Pan / Fader A TO ST (To stereo) This is an on/off switch for the signal sent from the MIX channel to the STEREO bus. To switch pages, click the tabs shown in the upper part of the window. INPUT PATCH page Here you can select the input port that is assigned to the input of each input channel. Except for the fact that you can resize the window, the basic operation is the same as in the PM5D's INPUT PATCH screen. OUTPUT PATCH page Here you can select the output port that is assigned to the input of each output channel. Except for the fact that you can resize the window, the basic operation is the same as in the PM5D's OUTPUT PATCH screen. 38 PM5D Editor Owner's Manual INPUT INSERT PATCH page Here you can assign input/output ports to the insert-in/out of each input channel. Select the output port in the left side of the screen, and the input port in the right side of the screen. Except for the fact that you can resize the window, the basic operation is the same as in the PM5D's INPUT INSERT PATCH screen. OUTPUT INSERT PATCH page Here you can assign input/output ports to the insert-in/out of each output channel. Select the output port in the left side of the screen, and the input port in the right side of the screen. Except for the fact that you can resize the window, the basic operation is the same as in the PM5D's OUTPUT INSERT PATCH screen. 39 PM5D Editor Owner's Manual DIRECT OUTPUT PATCH page Here you can select the output port that will directly output each input channel. Except for the fact that you can resize the window, the basic operation is the same as in the PM5D's DIRECT OUTPUT PATCH screen. PATCH LIST page Here you can view and edit the input patch and output patch settings. Input patch, output patch, and channel name data that was written to a CSV file by the PM5D itself can also be loaded into this page. Conversely, the settings in this page can be written to a CSV file that can be loaded into the PM5D. 40 PM5D Editor Owner's Manual 6 7 1 2 3 4 5 A Input channel number B Input channel name This is the number and name of the input channel. You can click the channel name box to edit the name in this page. C Input port This shows the input port assigned to the input channel. [. . . ] 58 Fade function enable/disable . . . . . . . . . 59 FADE TIME page . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 FADING ENABLE . . . . . . . . . . . . . . . . . . . . . . . . . 59 FILE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]