User manual YAMAHA PM1D V1.5 SUPPLEMENTARY MANUAL

[. . . ] PM1D System Software V1. 5 Supplementary Manual E PM1D System Software V1. 5 Supplementary Manual Copyright Copying or distributing this manual in part or in whole using any method without the written permission of Yamaha Corporation is prohibited. Trademarks Company names and product names are trademarks and registered trademarks of their respective owners. Symbols such as ® and TM are not explicitly given in this document. The illustrations and LCD screens as shown in this owner's manual are for instructional purposes only, and may appear somewhat different from those on your instrument. 2 Contents Contents Additions/changes in V1. 5. 4 Changes to the constantly-displayed screen. [. . . ] Furthermore, settings for the GPI connector of the engine can be made only from console 1. Access the MIDI/GPI/TC function GPI screen. Scroll the GPI IN list to show the INPUT port that you want to set. According to the character of the signal that is sent from the external device / external switch, set the TRIGGER field to Low Active (active when switch is grounded) or High Active (active when a high-level signal is input, or when open). 6. Scroll the list in the left part of the screen, and click the function that you want to assign. The PARAMETER field will show the parameters that are specific for that function. 40 Using GPI (General Purpose Interface) 7. As necessary, use the PARAMETER field located at the right to specify the parameters, and click the OK button. In the same way, make other GPI IN settings as desired. Hint 9. Operate the external device / external switch to send a control signal to the PM1D system. The function that is assigned to that GPI IN port will be executed on the PM1D system. Hint By displaying GPI IN CONSOLE / GPI IN ENGINE in the lower part of the screen, you can check the function that is assigned to each port (p. 10). Of the functions that can be assigned to GPI IN, Tap Tempo is explained in detail on page 51, so you may refer to that section as well. Using GPI OUT Here's how you can remotely control an external device by sending control signals from GPI OUT when a specific operation is performed on the PM1D system. Connect your GPI compatible external device to the GPI connector of the engine or console. · If you are using the PM1D system in Mirror 6. Scroll the list shown at the left side, click the trigger that you want to assign, and click the OK button. In the same way, make other GPI OUT settings as desired. Hint mode, GPI OUT output always operates in tandem for engines A and B. · If you are using the PM1D system in Dual Con- sole mode (p. 11), only the GPI connector of the currently-operated console can be used. It is not possible to modify the settings for the GPI connector of the other unit, or to receive control signals from the GPI connector of the other unit. Furthermore, settings for the GPI connector of the engine can be made only from console 1. Access the MIDI/GPI/TC function GPI screen. Scroll the GPI OUT list to display the OUTPUT port that you want to set. According to the character of the signal that your external device is able to receive, set the POLARITY field to either Low (grounded when active) or High (open when active). At the left of the ASSIGNED TRIGGER field, click the DIRECT ASSIGN button to open the GPI OUT SETUP popup window. You can use the TEST button in the GPI screen to test-transmit control signals from each GPI OUT according to the POLARITY and TRIGGER/TOGGLE/TALLY settings. This is a convenient way to verify that the external device will operate as you expect. Execute the operation that is assigned to GPI OUT. A control signal will be transmitted from the corresponding GPI OUT port. Hint If you want to use GPI OUT as a USER DEFINE destination, make settings in the USER DEFINE screen (p. 52). [. . . ] <Transmission> If [Program Change TX] is ON, this message will be transmitted from the selected MIDI OUT on the [Tx CH] channel (in the case of SINGLE mode), when a scene or effect library is recalled. In the case of MULTI mode, this will be transmitted on the MIDI channel according to the bank. If the recalled memory number is assigned to more than one program number, the program number for the lowest-numbered channel of the lowest-numbered bank will be transmitted. STATUS DATA 1100nnnn 0nnnnnnn Cn nn Program Change Program No. (0-127) The transmitted and received values are calculated as follows. (The same applies to the NRPN messages discussed later. ) Given the following: (128 or 16384 in the case of word data) / (number of parameter steps) = X . . . Y INT (( Y + 1) / 2 ) = Z Reception: If ( MIDI data -Z ) < 0, then parameter = 0 If (( MIDI data - Z ) / Z ) > MAX, then parameter = MAX 100 MIDI Data Format 1. 2 EXCLUSIVE MESSAGE (F0-F7) 1. 2. 1 MOTION CONTROL STATE (MCS) MMC STOP/PLAY/FORWARD/REWIND <Transmission> These messages are transmitted by assignment to USER DEFINE or GPI. [. . . ]