User manual YAMAHA PMT-H25

[. . . ] 14 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Always follow the instructions set forth in this manual when installing the projector using this bracket. Improper or inadequate installation could cause the projector to fall and injure someone. 2. The installation must be secure enough to bear the weight of the projector, the ceiling bracket, and other hardware indefinitely, and must also be secure enough to withstand vibration. Inadequate installation could cause the projector to fall and injure someone. 3. To ensure safety, all bolts and screws must be tightened securely. Loose bolts or screws could cause the projector to fall and injure someone. 4. [. . . ] Request that your dealer arrange to have the equipment installed. The customer should never attempt to suspend the projector from the ceiling. Improper installation could cause the ceiling bracket or the projector to fall and injure someone. Italiano Español Nederlands 15. Once the projector is installed, safety checks should be conducted on a regular basis. If the projector is used over an extended period of time, screws can become loose and the installation can become weaker due to the passage of time, vibration, etc. E-3 PACKING LIST Check that all of the following parts are included. PMT-L21 Ceiling bracket x 1 PMT-H25 Ceiling bracket x 1 Adjustment pole locking screws (M5) x 4 Common parts (The following parts are provided with each bracket. ) Projector mounting adapter x 1 Projector mounting screws (M4, pan head) x 4 Vertical angle adjustment screws (M6, hexagonal head) x 4 Safety brackets x 2 Safety bracket mounting screws (M4, pan head) x 4 Safety wires x 2 Safety wire mounting screws (M4, pan head) x 4 Installation Manual x 1 E-4 NAMES OF PARTS PMT-L21 English Français Horizontal angle adjustment screws Deutsch Ceiling bracket Svenska Mounting guide pin Italiano Vertical angle adjustment screws (There are also screws on the opposite side. ) Tilt angle adjustment screws (There are also screws on the opposite side. ) Español Projector mounting adapter Nederlands E-5 PMT-H25 Ceiling bracket Height locking screw Horizontal angle adjustment screw (four in total) Height adjustment pole Mounting guide pin Vertical angle adjustment screws (There are also screws on the opposite side. ) Tilt angle adjustment screws (There are also screws on the opposite side. ) Projector mounting adapter E-6 137 mm (5-3/8 inch) 175 mm (6-7/8 inch) 147. 3 mm (5-3/4 inch) 8 mm (5/16 inch) [Top View] PMT-L21 [Front View] Ø9 x 13 mm (Ø3/8 x 1/2 inch) (elliptical hole) 178 mm (7-1/16 inch) 184 mm (7-1/4 inch) 170. 5 mm (6-3/4 inch) 81 mm (3-3/16 inch) 196 mm (7-3/4 inch) 170 mm (6-11/16 inch) 140 mm (5-1/2 inch) Ø10 x 13 mm (Ø3/8 x 1/2 inch) (elliptical hole) 10° 10° Projector mounting adapter with the LPX-500 installed DIMENSIONS OF PARTS 170. 5 mm (6-3/4 inch) 178. 5 mm (7 inch) 170. 5 mm (6-3/4 inch) Ø9 mm (Ø3/8 inch) (hole) PMT-H25 [Front View] Ø9 x 13 mm (Ø3/8 x 1/2 inch) (elliptical hole) Ø9 mm (Ø3/8 inch) (hole) 120 mm (4-3/4 inch) 156 mm (6-1/8 inch) 192 mm (7-9/16 inch) 159 mm (6-1/4 inch) Ø10 mm (Ø3/8 inch) (hole) 10° 10° 8 mm (5/16 inch) [Top View] 226 mm (8-7/8 inch) 200 mm (7-7/8 inch) 832 to 1402 mm (32-3/4 to 55-3/16 inch) Ø10 x 13 mm (Ø3/8 x 1/2 inch) (elliptical hole) 777 to 1347 mm (30-9/16 to 53 inch) Ø8. 8 mm (Ø3/16 inch) (fully penetrating holes) with the LPX-500 installed 140 mm (5-1/2 inch) 175 mm (6-7/8 inch) 30 mm (1-3/16 inch) Ø10 mm (Ø3/8 inch) (hole) English Français Deutsch Svenska Italiano Español Nederlands E-7 887 to 1457 mm (34-15/16 to 57-3/8 inch) SCREEN SIZE AND SETTING-UP DISTANCE The distance between the projector and the screen (16:9) determines the actual image size. Recommended distance: 0. 9 to 13. 0 m (2. 9 to 12. 6 feet) While referring to the table below, position the projector so that the image size is smaller than the screen size. Screen size (cm [feet]) 30" (66 x 37 [2. 1 x 1. 2]) 40" (89 x 50 [2. 8 x 1. 6]) 60" (130 x 75 [4. 2 x 2. 4]) 80" (180 x 100 [5. 7 x 3. 2]) 100" (220 x 120 [7. 2 x 4. 1]) 200" (440 x 250 [14. 4 x 8. 2]) 300" (660 x 370 [21. 6 x 12. 1]) Approximate projection size* (m [feet]) Distance in Fig. A below (cm [feet]) 0. 9 to 1. 2 [2. 9 to 3. 9] 1. 2 to 1. 6 [3. 9 to 5. 2] 1. 8 to 2. 5 [5. 9 to 8. 2] 2. 5 to 3. 4 [8. 2 to 11. 1] 3. 1 to 4. 3 [10. 1 to 14. 1] 6. 3 to 8. 6 [20. 6 to 28. 2] 9. 5 to 13. 0 [31. 1 to 42. 6] 5. 0 to 5. 1 [0. 16 to 0. 17] 6. 7 to 6. 8 [0. 22 to 0. 22] 10. 2 [0. 33] 13. 6 to 13. 7 [0. 45 to 0. 45] 17. 0 to 17. 1 [0. 56 to 0. 56] 34. 0 to 34. 3 [1. 12 to 1. 13] 51. 0 to 51. 4 [1. 67 to 1. 69] * Distance and dimensions should be used as a guide for installation. The actual distance will vary depending on projection conditions. Distance from center of 5. 0 to lens to top edge of screen 5. 1 (cm) 6. 7 to 6. 8 10. 2 13. 6 to 17. 0 to 13. 7 17. 1 34. 0 to 34. 3 51. 0 to 51. 4 Distance from center of ceiling bracket to front edge of projector: Approx. 12 cm 0. 9 to 1. 2 1. 2 to 1. 6 30" (66 × 37) 40" (89 × 50) 60" (130 × 75) 80" (180 × 100) 1. 8 to 2. 5 2. 5 to 3. 4 3. 1 to 4. 3 6. 3 to 8. 6 9. 5 to 13. 0 100" (220 × 120) Distance from ceiling surface to center of lens: PMT-L21: Approx. 19 cm PMT-H25: 89 to 146 cm 200" (440 × 250) Screen size (cm) 300" (660 × 370) Approximate projection size (m) Notes · The projection distance is the horizontal distance from the surface of the projector lens to the surface of the screen. In the case of the LPX-500, the surface of the lens is recessed by approximately 3 cm from its exterior. · Although the vertical angle of the ceiling bracket can be adjusted in a range of ±15°, a large angle adjustment may distort the projected image. We recommend you to adjust both the angle of the ceiling bracket and the angle of the screen. · The lens of the LPX-500 allows a zoom ration of up to about 1. 35. The image size at the maximum zoom setting is about 1. 35 times bigger than the image size at the minimum zoom setting. · The image size will be reduced when keystone correction is carried out. E-8 PMT-H25 height adjustment English The height adjustment pole for the PMT-H25 has holes spaced 3 cm apart that can be used to adjust the height. When the bracket is shipped from the factory, the pole is set at the shortest height. Follow the procedure described below to adjust the pole to the appropriate height. For details on the appropriate height, refer to "SCREEN SIZE AND SETTING-UP DISTANCE" on page 8. Français [Adjustment Procedure] 1 Remove the safety pin. 2 Loosen the nut, and then remove the height locking screw. Caution · Removing the height locking screw will unlock the height adjustment pole from the ceiling bracket. In order to ensure that the height adjustment pole does not fall, always hold the pole while performing this work. [. . . ] · First, select a projection size using the zoom feature, and then adjust the angle. 1 Adjust the horizontal angle. Adjust the projector so that the projected image is centered horizontally on the screen, and then tighten the horizontal angle adjustment screws (2 on the PMT-L21, 4 on the PMT-H25). Left Right 10° 10° Maximum angle of adjustment: ±10° (PMT-L21) Horizontal angle adjustment screws (PMT-H25) E-14 2 Adjust the vertical angle. English Adjust the projector so that the projected image is centered vertically on the screen, and then tighten the four vertical angle adjustment screws. Top Français 15° 15° Deutsch Maximum angle of adjustment: ±15° (PMT-L21) Bottom Svenska Vertical angle adjustment screws (There are also screws located on the opposite side. ) 3 Adjust the tilt angle. Italiano Español Adjust the projector so that the projected image is not tilted at all compared to the screen, and then tighten the four tilt angle adjustment screws. (PMT-L21) Tilt angle adjustment screws (There are also screws located on the opposite side. ) Nederlands 10° 10° Maximum angle of adjustment: ±10° If the projector still needs further adjustment, start over from step 1. After adjustment is completed, make sure that the projector is secured in place. E-15 SPECIFICATIONS Product Name Model No. Height Adjustment range Vertical angle Horizontal angle Tilt angle Dimensions of ceiling bracket (W × D × H) Dimensions of adapter (W × D × H) Weight PMT-L21 94 mm (3-11/16 inch) (fixed) ±15° ±10° ±10° Ceiling Mount Bracket PMT-H25 789 to 1359 mm (31-1/16 to 53-1/2 inch) (variable in 30 mm (1-3/16-inch) steps) ±15° ±10° ±10° 176 × 226 × 789 to 1359 mm (6-15/16 × 8-7/8 × 31-1/16 to 53-1/2 inch) 156 × 196 × 94 mm (6-1/8 × 7-3/4 × 3-11/16 inch) (Height is variable in 30-mm (1-3/16-inch) steps) 362. 5 × 179 × 77 mm (14-1/4 × 7 × 3 inch) 2. 2 kg (4 lbs 14 oz) 4. 0 kg (8 lbs 13 oz) · Specifications are subject to change without notice. E-16 Additional Installation Information / Informations de montage supplémentaires / Zusätzliche Installationshinweise / Extra anvisning angående montering / Informazione di installazione addizionale / Información adicional para la instalación / Aanvullende installatie-informatie PMT-L21 Side View PMT-L21 Front View 137 mm (5-3/8 inch) 81 mm (3-3/16 inch) Wall 111 mm (4-3/8 inch) 159 mm (6-3/16 inch) More than 361 mm (14-3/16 inch) 122 mm (4-13/16 inch) 108. 5 mm (4-1/4 inch) 409 mm (16-1/8 inch) Projection Direction PMT-H25 Front View PMT-H25 Side View 777­1347 mm (30-9/16­53 inch) Ø8. 8 mm (Ø3/16 inch) (fully penetrating holes) 832­1402 mm (32-3/4­55-3/16 inch) Wall More than 361 mm (14-3/16 inch) Projection Direction 108. 5 mm (4-1/4 inch) 409 mm (16-1/8 inch) Be sure to align the horizontal center of your screen with the projector's lens, not the center of the projector. Alignez la lentille du projecteur et non le centre du projecteur avec le centre horizontal de l'écran. [. . . ]