User manual YAMAHA PMT-L11-H15

[. . . ] 4 Names of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Dimensions of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Guidelines for the Projector Installation Position and Screen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Installation Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Never hang from the projector or the ceiling bracket. English Français Hanging from the projector or the ceiling bracket could cause the projector or the ceiling bracket to fall and injure someone. 10. Do not install the projector in a location near an air conditioning vent or in a location subject to vibration. Such conditions could have an adverse effect on the projector, and could even cause a fire or electric shock. 11. Do not install the projector in a location that is subject to high levels of dust or humidity. Dust accumulating inside the projector could cause a short circuit that in turn could cause a fire or electric shock. Deutsch 12. Do not install the projector in a location that is exposed to direct sunlight or in a location that is subject to extreme fluctuations in temperature (such as near an air conditioner). Such conditions can cause the projector housing to warp or to become discolored. Svenska 13. Do not wipe the exterior of the ceiling bracket with benzene, paint thinner or cleaning compounds. Doing so could damage the finish. 14. Special techniques and experience are essential when installing the projector using this bracket. Request that your dealer arrange to have the equipment installed. The customer should never attempt to suspend the projector from the ceiling. Improper installation could cause the ceiling bracket or the projector to fall and injure someone. Italiano Español Nederlands 15. Once the projector is installed, safety checks should be conducted on a regular basis. If the projector is used over an extended period of time, screws can become loose and the installation can become weaker due to the passage of time, vibration, etc. E-3 Packing List Confirm that all of the parts are present. PMT-L11 Ceiling bracket x 1 PMT-H15 Ceiling bracket x 1 Adjustment pole locking screws (M5) x 4 Common Components (The following parts are provided with each bracket. ) Projector mounting adapter x 1 Projector mounting screws (M6, pan head) x 4 Safety brackets x 2 Vertical angle adjustment screws (M6, hexagonal head) x 4 Safety bracket mounting screws (M4, pan head) x 4 Safety wires x 2 Safety wire mounting screws (M4, pan head) x 4 E-4 Names of Parts PMT-L11 English Français Horizontal angle adjustment screws Deutsch Ceiling bracket Svenska Mounting guide pin Italiano Tilt angle adjustment screws (There are also screws on the opposite side. ) Vertical angle adjustment screws (There are also screws on the opposite side. ) Projector mounting adapter Español Nederlands E-5 PMT-H15 Ceiling bracket Horizontal angle adjustment screw (four in total) Height locking screw Height adjustment pole Mounting guide pin Tilt angle adjustment screws (There are also screws on the opposite side. ) Vertical angle adjustment screws (There are also screws on the opposite side. ) Projector mounting adapter E-6 Ø9 x 13 mm Ø3/8 x 1/2 inch (elliptical hole) 10° 10° 196 mm 7-3/4 inch 170 mm 6-11/16 inch 140 mm 5-1/2 inch 81 mm 3-3/16 inch Ø10 x 13 mm Ø3/8 x 1/2 inch (elliptical hole) [Top View] PMT-L11 230 mm 9-9/16 inch 200 mm 7-7/8 inch 190 mm 7-1/2 inch 212 mm 8-3/8 inch [Front View] Projector Mounting Adapter Dimensions of Parts with the DPX-1 installed (lens center) Ø9 mm Ø3/8 inch (hole) 201. 65 mm 7-15/16 inch Ø9 x 13 mm Ø3/8 x 1/2 inch (elliptical hole) Ø9 mm Ø3/8 inch (hole) 120 mm 4-3/4 inch 156 mm 6-1/8 inch Ø10 mm Ø3/8 inch (hole) 10° 10° 55 mm 2-3/16 inch 80 mm 3-1/8 inch [Top View] PMT-H15 [Front View] 226 mm 8-7/8 inch 200 mm 7-7/8 inch Ø10 x 13 mm Ø3/8 x 1/2 inch (elliptical hole) 777 to 1347 mm 30-9/16 to 53 inch Ø8. 8 mm Ø3/16 inch (fully penetrating holes) 30 mm 1-3/16 inch with the DPX-1 installed (lens center) 140 mm 5-1/2 inch 175 mm 6-7/8 inch Ø10 mm Ø3/8 inch (hole) English Français Italiano Deutsch Svenska Español Nederlands E-7 896. 65 to 1466. 65 mm 35-5/16 to 57-3/4 inch Guidelines for the Projector Installation Position and Screen Size · The relationship between the projection distance and the screen size is shown below. Use these values as guidelines for determining the installation position. Ceiling Distance from ceiling installation surface to center of lens PMT-L11: 20 cm (7-7/8 inch) PMT-H15: 90 to 147 cm (35-7/16 to 57-7/8 inch) (can be adjusted in 3 cm (1-3/16 inch) steps) Distance from center of projector's lens to top edge of screen (See the owner's manual for the projector. ) Screen Distance from the center of the ceiling bracket to the front edge of the projector: approximately 20 cm (7-7/8 inch) Projection distance (See the diagram below. ) When using a 4:3 Screen Screen size (inch) 60 80 100 120 150 200 Projection distance (Wide/Tele. ) (m) (feet, inch) 2. 4 ­ 2. 9 7' 10" ­ 9' 6" 3. 2 ­ 3. 9 10' 6" ­ 12' 10" 4. 0 ­ 4. 9 13' 1" ­ 16' 4. 8 ­ 5. 8 15' 9" ­ 19' 6. 1 ­ 7. 3 20' ­ 23' 11" 8. 1 ­ 9. 8 26' 7" ­ 32' 2" Projection distance Wid Tele . de Zoom function Wi de Tel e . Sma ller Scre en s ize Larg er When using a 16:9 Screen Screen size (inch) 60 80 100 120 150 200 Projection distance (Wide/Tele. ) (m) (feet, inch) 2. 6 ­ 3. 2 8' 6" ­ 10' 6" 3. 5 ­ 4. 2 11' 6" ­ 13' 9" 4. 4 ­ 5. 3 14' 5" ­ 17' 5" 5. 3 ­ 6. 4 17' 5" ­ 21' 6. 6 ­ 8. 0 21' 8" ­ 26' 3" 8. 8 ­ 10. 6 28' 10" ­ 34' 9" Projection distance Wid Tele. e Sma ller Scre en s ize Larg er Zoom function Wi de Tel e . Cautions · The projection distance is the horizontal distance from the surface of the projector lens to the surface of the screen. In the case of the DPX-1, the surface of the lens is recessed by approximately 4 cm (1-9/16 inch) from its exterior. · Although the ceiling bracket permits adjustment of the vertical angle of the projector over a range of ±15°, a large angle adjustment will distort the projected image somewhat. Therefore, we recommend adjusting both the angle of the projector and the angle of the screen. Adjustment Through Digital Lens Shift When "SCREEN ASPECT" is set to 16:9 in the SETUP menu, it is possible to use the projector's digital shift function to adjust the distance from the center of the projector's lens to the top edge of the screen. The range of adjustment is indicated at right. E-8 Screen size (inch) 60 80 100 120 150 200 Distance to top edge of screen (cm) (inch) 19 ­ 44 7-1/2 to 17-5/16 26 ­ 59 10-1/4 to 23-1/4 32 ­ 74 12-5/8 to 29-1/8 39 ­ 89 15-3/8 to 35 49 ­ 111 19-3/8 to 43-3/4 65 ­ 145 25-5/8 to 57 PMT-H15 Height Adjustment English Français The height adjustment pole for the PMT-H15 has holes spaced 3 cm apart that can be used to adjust the height. When the bracket is shipped from the factory, the pole is set at the shortest height. Follow the procedure described below to adjust the pole to the appropriate height. [. . . ] 2 Screw the bolts into the anchor nuts. Anchor nut Cautions · Make sure that the anchor nuts are strong enough to bear the weight of the projector and the ceiling bracket. (Use two screws on the left side and two screws on the right. ) Español (PMT-L11) Nederlands Vertical angle adjustment screw (Hand-tighten the other side also. ) E-13 Adjusting the Projection Angle Prior to Adjustment · After reading the owner's manual for the projector, turn the projector on, and project an image. · Check the INSTALLATION item in the SETUP menu, and set the installation status. If projecting from the front of the unit, select "FRONT/CEILING;" if projecting from the rear of the unit, select "REAR/ CEILING. " · Select a projection size using the zoom feature, and then adjust the angle. 1 Adjust the horizontal angle. Adjust the projector so that the projected image is centered horizontally on the screen, and then tighten the horizontal angle adjustment screws. Left Right 10° 10° Maximum angle of adjustment: ±10° (PMT-L11) Horizontal angle adjustment screws (PMT-H15) E-14 2 Adjust the vertical angle. English Adjust the projector so that the projected image is centered vertically on the screen, and then tighten the four vertical angle adjustment screws. Top Français 15° 15° Deutsch Maximum angle of adjustment: ±15° (PMT-L11) Bottom Svenska Vertical angle adjustment screws (There are also screws located on the opposite side. ) 3 Adjust the tilt angle. Italiano Español Adjust the projector so that the projected image is not tilted at all compared to the screen, and then tighten the four tilt angle adjustment screws. (PMT-L11) Tilt angle adjustment screws (There are also screws located on the opposite side. ) Nederlands 10° 10° Maximum angle of adjustment: ±10° If the projector still needs further adjustment, start over from step 1. [. . . ]