User manual YAMAHA PREMIUM EF12000DE

[. . . ] EPA REGULATIONS FOR SMALL NON-ROAD ENGINES (EMISSION COMPLIANCE PERIOD OF 1000 HOURS) AND CALIFORNIA SI SORE's. EH63 . 64 . 65 5 6 - 3- - 4- - 5- - 6- - 7- - 8- - 9- - 10 - - 11 - 1) Check fuel level at fuel level gauge. 2) If fuel level is low, refill with unleaded automotive gasoline. [. . . ] Always use the best grade and clean oil. Contaminated oil, poor quality oil and shortage of oil cause damage to engine or shorten the engine life. OIL CAPACITY : 1. 55 L (1. 36 lmp qt, 1. 64 US qt) OIL FILLER CAP OIL DRAIN PLUG (ON BOTH SIDE) ENGINE OIL FILTER REPLACEMENT Initial engine oil filter replacement should be performed after 20 hours of operation. Thereafter replace the engine oil filter every 200 hours. OIL FILTER When installing a new oil filter, apply oil to O-ring, attach the oil filter in position and tighten 2/3 turns by hand or with wrench after touching the O-ring to the sealing surface of engine. Run the engine for a minute ; stop the engine and check for oil leakage around the oil filter and recheck the oil level. CAUTION : To prevent injury, pay attention to the spilled hot engine oil when replacing engine oil filter. - 27 - - 28 - - 29 - - 30 - - 31 - SPARK ARRESTER SPARK ARRESTER In a dry or wooded area, it is recommendable to use the engine with a spark arrester. Some areas require the use of a spark arrester. Please check your local laws and regulations before operating your engine. The spark arrester must be cleaned regularly to keep it functioning as designed. A clogged spark arrester : Prevents the flow of exhaust gas Reduces engine output Increases fuel consumption Makes starting difficult If the engine has been running, the muffler and the spark arrester will be very hot. Allow the muffler to cool before cleaning the spark arrester. How to remove the spark arrester MUFFLER 1. Remove the flange bolts from the muffler cover and remove the muffler cover. Remove the special screw from the spark arrester and remove the spark arrester from the muffler. SPARK ARRESTER SCREEN SCREW SPARK ARESSTER SCREEN Clean the spark arrester screen Use a brush to remove carbon deposits from the spark arrester screen. Be careful to avoid damaging the screen. The spark arrester must be free of breaks and holes. Replace the spark arrester if it is damaged. Install the spark arrester, and muffler protector in the reverse order of disassembly. - 32 - PREPARATION FOR STORAGE The following procedures should be followed prior to storage of your generator for a period of 6 months or longer. Drain fuel from fuel tank and strainer (cup) carefully by disconnecting the fuel line. Gasoline left in the fuel tank will eventually deteriorate making engine-starting difficult. [. . . ] ] shows dry weight with castors installed. - 36 - WIRING DIAGRAM CONTROL BOX Auto choke (Bimetal) Ignition coil R LGrn R/W Blk/W Blk (AC output) W W W W Fuel cut R Blk/W Blk W Grn Gry W W Oil pressure warning lamp (Red) W Idle solenoid 1 5 123 456 Exciting coil (AVR) Y Y Charge coil Org R 2 LBlu 3 4 Idle control unit Y LBlu Electronic control unit 13 12 11 10 9 8 7 Org Grn/Y Brn Org Grn/Y Org Grn Gry -M +M B L. IG ST OFF ON START Economy switch Org R Grn/Y Grn/Y Blk Blk Electric starter Magnetic switch Grn Key switch Blk R Regulator R15 Blk15 to earth terminal Gry (AC 120V) - + ST Relay Battery 12V Oil pressure switch Grn Org Blk Grn/Y Gry R Connector (Remote control) AC output receptacle (120V) REC1 GENERATOR CONTROL BOX Fuse Blk R AC output receptacle (120/240V) REC3 AC output receptacle (120/240V) REC4 Connector Remoto control Blk Grn/Y Blk AC Winding 1 Field Winding Idle control unit w R w Pilot lamp Voltmeter Blu Hr R Blk V PL Brush Brush AC Winding 2 AC otuput receptacle(120V) REC2 W LGrn Brn W Blk Blk W Brn LGrn LGrn Brn (4P) AVR Engine Exciting coil Y Y Gr n/Y Earth(Ground) terminal Grn/Y Grn/Y Wiring color cord Blk Blk/W Blu LBlu Brn Black Black/White Blue Light blue Brown Brn/W Grn Grn/W Org Gry Brown/White Green Green/White Orange Gray R W Y Pik Grn/Y Red White Yellow Pink Green/Yellow Blk/R R/W LGrn Black/Red Red/White Light green - 37 - Grn/Y Auxiliary Winding for Condenser No-fuse breaker W W Key switch Idle control unit OPTIONAL PARTS "HOW-TO" INSTALL THE WHEEL (1) Checking of supplied accessories (2) Tool preparation Hoist or square bar (100 mm (3. 94 in) by 100 mm (3. 94 in), length : 700 mm (27. 56 in)) Plier Spanner or socket wrench (12 mm (0. 472 in)), 2 units (3) Installation procedures (a) Raise the generator by about 100 mm (3. 94 in), with hoist or with square bar put under the bottom panel. , , stopper , using clamp and wheel , to (b) Attach wheel mounting parts wheel shaft . If moving turns out to be too compliThen check that wheel cated, assemble them together using grease. [. . . ]