User manual YAMAHA PSS-480

[. . . ] Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. [. . . ] In addition, you can use the WITH MATRIX SEND button to enable Recall Safe for the on/off status and send level of the signals sent from output channels to MATRIX buses. PSS-480 SAFE button LS9-32 NOTE These buttons correspond to the following parameters. Button name ALL EQ DYNA 1 FADER CH ON WITH MATRIX SEND Corresponding parameters All parameters (except for WITH MATRIX SEND) EQ settings (including ATT) Dynamics 1 settings Fader positions On/off status of [ON] keys On/off status and send level of signals sent from MIX channels / STEREO/MONO channels to MATRIX buses · Simply selecting a parameter in step 3 does not enable Recall Safe. To turn Recall Safe on/off, you must also perform the operation of step 4. HINT · In the CH RECALL SAFE field, the color of the highlight will be green if the ALL button was selected in step 3, or blue if buttons other than ALL were selected. · If you press the CLEAR ALL button, Recall Safe will be defeated for all channels for which it is enabled (i. e. , the highlighted channels). · You can also switch Recall Safe on/off in the SELECTED CH VIEW screen's SAFE field ( p. 88). NOTE · If you turn on the ALL button, all buttons will be turned off except for the WITH MATRIX SEND button located in the SAFE PARAMETER field. · You can switch the WITH MATRIX SEND button on/off while the ALL button is left on. 142 PSS-480/32 Owner's Manual Using the Recall Safe function · Using the Fade function 5 If you want to enable Recall Safe for global parameters, turn on the desired buttons in the GLOBAL field. These buttons correspond to the following parameters. Button name INPUT PATCH INPUT NAME OUTPUT PATCH OUTPUT NAME 1­8 Corresponding parameters Input port patching Input channel name Output port patching Output channel name Rack 1­8 settings 6 When you've finished making settings, execute a Recall operation. Only the selected channel(s) and parameter(s) will be excluded from Recall operations. 124) and the MIX/MATRIX bus settings in the SYSTEM SETUP screen ( p. 213) are not subject to Recall Safe; the settings of the recalled scene will always be reproduced. This means that if Recall Safe is enabled for one of several channels included in a link group or one of two MIX/MATRIX channels set to stereo, the parameter settings of that channel may differ from those of the other channel(s) when you recall a scene. In such cases, the applicable parameter will be automatically re-linked the next time it is operated. HINT · The Recall Safe function can be used in conjunction with the Focus function ( p. Channels or parameters that are excluded from Recall operations by either Focus or Recall Safe will not be recalled. You can select the following signals as the monitor source. · · · · · STEREO channel output signal MONO channel output signal STEREO + MONO channel output signal 2TR IN DIGITAL jack input signal INPUT channels 15/16 {31/32} input signal · USB memory recorder output signal · Any combination of up to eight signals from the STEREO, MONO, MIX, and MATRIX channels, the USB memory recorder output signal, INPUT channel 15/ 16 {31/32}, and the 2TR IN DIGITAL jack input signal The Cue function lets you check an individual selected channel by temporarily sending it from the output jacks assigned to the MONITOR OUT channel or from the PHONES OUT jack. When you press the top panel [CUE] key, the cue signal of the corresponding channel is sent as the monitor output from the selected output port. NOTE · The cue signal is sent to the same output destination as the monitor signal. Be aware that for this reason, the cue signal will no longer be sent to the connected monitor speakers if you turn off the Monitor output. However, the cue signal will always be sent to the PHONES OUT jack. CUE LR CUE TRIM (INPUT/OUTPUT/DCA) PHONES OUT LR MONO METER CUE L METER CUE R CUE LOGIC 2 DA Tip Ring Sleeve PHONES LEVEL [PHONES] CUE L CUE R PHONES LEVEL LINK PHONES L PHONES R To PHONES OUT To PHONES OUT 2TRD L, R INPUT 15, 16{31, 32} PLAYBACK OUT MONITOR SELECT 2TRD L, R INPUT 15, 16{31, 32} PLAYBACK OUT MONITOR R MONITOR MONO(C) METER MONITOR R METER MONITOR MONO(C) DIMMER STEREO OUT L, R STEREO OUT MONO(C) STEREO OUT L, C, R MONITOR L MONO METER MONITOR L MONITOR OUT L MONITOR OUT R MONITOR OUT MONO(C) To OUTPUT PATCH To OUTPUT PATCH To OUTPUT PATCH STEREO OUT L, R STEREO OUT MONO(C) MIX OUT1-16 MATRIX OUT1-8 DEFINE MIX (MAX:8ch) ON TALKBACK ON MONITOR DIMM ON +MONO(C) MONITOR LEVEL MONITOR SELECT MONITOR LEVEL Selects the monitor source. METER Detects and indicates the level of the monitor signal or cue signal. DIMMER Adjusts the level of the monitor/cue signal. This affects the output jacks that are assigned to the MONITOR OUT L/R/C channels, and also the PHONES OUT jack. ON (On/off) Turns the monitor output on/off. PHONES LEVEL (Headphone level) Attenuates the monitor/cue signal by a fixed amount. Adjusts the output level of only the PHONES OUT jack. PSS-480/32 Owner's Manual 145 Monitor/Cue The following diagram shows the monitor/cue signal flow. 14 Using the Monitor function Using the Monitor function This section explains how to select the desired monitor source, and monitor it from the PHONES OUT jack or external monitor speakers. 1 Connect your monitor system to the rear panel OMNI OUT jacks, 2TR OUT DIGITAL jack, or an I/O card installed in a slot. The monitor signal can be sent to any desired output jack or output channel. If you're monitoring through headphones, make sure that your headphones are connected to the front panel PHONES OUT jack. E MONITOR LEVEL knob Adjusts the output level of the monitor signal. F DIMMER field The Dimmer function which temporarily attenuates the monitor signal can be switched on/off here. Use the knob in this field to adjust the amount of attenuation. G TALKBACK DIMMER field If Talkback is enabled, this will indicate the on/off status of the Talkback Dimmer function which automatically attenuates the monitor signal. Here you can also specify the amount of attenuation applied by the talkback dimmer. H Meter field This indicates the level of the monitor signal. [. . . ] Output [+24dBu] CASCADE IN CASCADE OUT OUT +30 +24 +20 +10 +4 0 -10 -20 -30 -40 -50 -60 1 Nominal Input [+10dBu] OUT OUT Nominal Output [+4dBu] PHONES Max Output (150mW@8) Nominal Output (75mW@8) [The position of the level control is 10dB lowered from Max] 2 Max. Input [-42dBu] OMNI OUT1-16/8 [Default setting] 2 Nominal Input [-62dBu] -70 1 INPUT 1-32/16 (GAIN MIN. ) 2 INPUT 1-32/16 (GAIN MAX. ) -80 -90 -100 -110 -120 -130 -140 -150 -160 Max. DSP Noise Floor -170 -180 -190 [0dBu = 0. 775Vrms] [0dBFS = Full Scale] For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. [. . . ]