User manual YAMAHA PSS-795

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] What is the music saying and what instrument or technique is being used to drive the message?That's where the focus of your mix should be. You're using a high-tech tool to do the mixing, but the mix itself is as much art as the music. Approach it that way and your mixes will become a vital part of the music. 18 PSS-795 Owner's Manual Reference Reference Front & Rear Panels Controls on Each Channel Channels 1 to 8 (Monaural) Channels 9/10 to 15/16 (Stereo) 1 INPUT A and INPUT B Jacks (Channels 1 to 8) You can connect an input source to either jack. Be sure to set the [26 dB] switch 4 to match the type of device you are connecting. INPUT A: A balanced XLR-type microphone input jack (1:Ground; 2:Hot; 3:Cold). If you are connecting a condenser microphone, be sure to turn the PHANTOM switch c to its ON position. Cold (­) 1 2 Ground Hot (+) INPUT B: A TRS phone-type balanced line input jack (T: hot, R: cold, S: ground). Accepts both balanced and unbalanced line input. R: Cold (­) S: Ground T: Hot (+) CAUTION When using phantom power, do not connect any devices other than condenser microphones to the XLR input jacks. Other devices may be damaged if connected to phantom power. This precaution does not apply to balanced dynamic microphones, however, as these will not be affected by phantom power. On any given channel, you may use either INPUT A or INPUT B, but not both. Turning the knob to the right boosts the corresponding frequency band, while turning to the left attenuates the band. On channels 1 to 8, the MID range is controlled by two knobs. The upper knob sets the center frequency for the mid range, while the lower knob sets the attenuation (counterclockwise) or boost (clockwise) for the range. (Again, setting the lower knob to " " produces a flat response. ) On stereo channel pairs 9/10 to 15/16 the mid-range frequency is fixed at 2. 5kHz, so only one MID knob is provided. The following table shows the equalization type, the base frequency, and the maximum cut/boost for each of the three bands. Band HIGH MID LOW Type Shelving Peaking Shelving Base Frequency 10 kHz 250 Hz to 5 kHz variable (CHs 1 to 8) 2. 5 kHz (CHs 9/10 to 15/16) 100 Hz ±15 dB Maximum Cut/Boost B PAN Control (Channels 1 to 8); BAL Control (Channels 9/10 to 15/16) The PAN control determines the positioning of the channel's signal on the Stereo L and R buses. The BAL control sets the balance between left and right channels. Signals into the L input (odd channel) feed to the Stereo L bus; signals into the R input (even channel) feed to the Stereo R bus. C ON Switch Switches the channel on or off. (The indicator lights up if the channel is on. ) Be sure to turn on all the channels that you wish to use. If you switch the channel off, you cut off all of its signal feed into the Stereo, AUX, and EFFECT buses. NOTE To reduce noise, turn off all unused channels. D PEAK Indicator Detects the peak level of the post-equalizer signal, and lights up red when the level reaches 3 dB below the clipping level. E SIGNAL Indicator Lights up when a signal is being input into the channel. F PFL (Pre-Fader Listen) Switch Set this switch on to feed the channel's pre-fader signal into the PFL bus, so that it can be monitored at the PHONES jack. To set the switch on, press it in so that it lights up. NOTE 9 AUX1/2 Knobs (PRE/POST) Each knob adjusts the channel's signal level into the AUX1/2 bus. The knob should generally be set close to the " " position. [. . . ] [-16dBu] ST CH IN [-10dBu] Clip Level ST CH MIC [-16dBu] CH fader [-10dBu] -20dBu -30dBu CH INPUT (PAD ON) GAIN Max. [-34dBu] -40dBu -50dBu CH INPUT (PAD OFF) GAIN Max. [-60dBu] -60dBu ST CH MIC [-60dBu] PSS-795 Owner's Manual -70dBu Specifications Reference 39 For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. [. . . ]