User manual YAMAHA RI8-D/RO8-D RI8-D/RO8-D UPDATE GUIDE

[. . . ] ・ Windows is a registered trademark of Microsoft ® Corporation in the United States and other countries. ・ The company names and product names in this document are the trademarks or registered trademarks of their respective companies. 1 ■ Checking the version number ・ You may check the Ri/Ro main firmware version number from the firmware update program (Rio Update Program) or the Dante Controller of Audinate. Rio Update Program Dante Controller (Device View) ・ You may check the Dante firmware version number from the I/O DEVICE screen of CL series or Dante Firmware Update Manager of Audinate. CL (I/O DEVICE screen) Dante Controller (Device View) 2 ■ Preparing for the update You will need the following items ready to execute the update procedure. ● A Windows computer equipped with the following conditions: OS CPU HDD Connector Windows 7 Windows XP 250MB or more An Ethernet connector that supports a data transfer rate of 100Mbps or higher Ultimate / Professional / Home Premium Professional SP3 or later / Home Edition SP3 or later Intel Pentium 1. 2GHz or Intel Celeron 1. 7GHz or higher ● An Ethernet cable (CAT5e or higher recommended. Straight or cross. ) ● The Ri/Ro firmware Download the latest firmware from the following URL. http://www. yamahaproaudio. com/downloads/ ● The Dante firmware update program Download the latest program from the following URL. http://www. yamahaproaudio. com/downloads/ ■ Update procedure sequence Update each firmware component in the following sequence. [. . . ] ・ Before starting the update program, quit all other programs. While the update is in progress, do not start any other programs or switch between windows. ・ If your computer enters Sleep or Energy Save mode, data transfer to the device may stop. Therefore, you should disable these functions to prevent this from happening. We also recommend that you do not use any screen saver or similar background programs. 1. Take note of the dip switch settings on the Ri/Ro unit front panel. Follow the procedure below to change dip switch settings. Take note of the original dip switch settings in order to restore the settings when the Dante firmware update is completed. 3. Disconnect the Ethernet cable from the Dante [PRIMARY] connector and [SECONDARY] connector on the rear panel of the Ri/Ro unit. 4. Pull the dip switch 4 on the Ri/Ro unit front panel down (ON) and turn the power on with the other switches remaining in their up positions (OFF). 5. After the orange [SYNC] indicator flashes twice periodically on the front panel of the Ri/Ro unit, turn off the power. 6. Connect the Dante [PRIMARY] connector on the rear panel of the Ri/Ro unit to the Ethernet connector on the computer using an Ethernet cable. 7 7. Pull the dip switches 4 and 8 on the Ri/Ro unit front panel down (ON) and turn the power on with the other switches remaining in their up positions (OFF). The right side of the [SYSTEM] indicator and the [SYNC] indicator start flashing and the unit is activated in update mode. 8. Double-click [update. exe]. The Ri/Ro Update Program will start up. Make sure that the fields in the "File" section indicate as follows: file name ：RI8RO8_PROG. bin product name ：Ri8_Ro8_PROG Version ：Version number to which the firmware will be updated ・When running under Windows 7, the "User Account Control" dialog box may appear. Click [Continue] or [Yes]. 9. Click the [Connection] button in the “Connect and Update” column. The “product name” field will display “Ri8_Ro8, ” and the “version” field will display the version number of the Ri/Ro firmware. ・If these fields are empty, your computer may not be properly connected to the Ri/Ro. Please make sure that the cable is not disconnected or damaged, that the TCP/IP settings are correct, and that the Ri/Ro has started in Update mode. 10. Click the [Update] button in the “Connect and Update” column. The update operation will begin. The update will take about 30 seconds. During the update operation, do not turn off the power to the unit or disconnect the cable. If update fails due to disconnection of the power cable during the update, or due to other reasons, the device may become inoperative. 11. When the “Connect and Update” section displays the message “Updating was completed. Close this Update Program” click the [X] button in the upper-right corner of the program window to close the program. 12. Turn off the power to Ri/Ro. 8 ■ Computer TCP/IP setting (for Dante) To update Dante firmware, configure computer TCP/IP settings. Windows 7 1. Select [Start]→[Control Panel], then click or double-click [Network and Sharing Center] or [View network status and tasks]. The “Network and Sharing Center” is displayed. 2. Click [Manage network connection] or [Change Adapter settings] from the “Tasks” list located in the left side of “Network and Sharing Center” window, then double-click [Local Area Connection]. The "Local Area Connection Status" dialog box will be displayed. ・The "User Account Control" dialog box may appear. ・If the "Local Area Connection properties" dialog box appears, skip ahead to step 4. 3. Click [Properties]. The “Local Area Connection properties” dialog box will be displayed. ・The "User Account Control" dialog box may appear. Click [Continue] or [Yes]. 4. Select [Internet Protocol Version 4 (TCP/IPv4)], then click [Properties]. The "Internet Protocol Version 4(TCP/IPv4) Protocol" dialog box will be displayed. 5. Click [Obtain an IP address automatically]. 6. Click [OK]. 9 Windows XP 1. Select [Start] → [Control Panel]. The "Control Panel" is displayed. 2. 3. If the control panel appears as category view, click [Switch to Classic View]. [. . . ] This section explains the error numbers, the English strings, and the appropriate action to take. ・ If the same error message appears each time you try to update, the device may need repairing, in which case you should contact your Yamaha dealer. Cause Number Possible Solution Make sure that the computer is connected to the Ri/Ro correctly, then restart the Rio Update Program and the Ri/Ro unit. (→P. 7) [ERROR:009] The Ri/Ro is not engaged in Update mode. [. . . ]