User manual YAMAHA RS130 ASSEMBLY MANUAL

[. . . ] If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product, it may result in deterioration. ASSEMBLY INSTRUCTIONS INTRODUCTION Thank you for purchasing the Yamaha Electronic Drum Rack System RS130. [. . . ] If anything is missing, please contact the dealer from whom you purchased the unit. * Before assembling the rack stand, make sure all of the parts shown below are included. PRECAUTIONS Before using, please read this "Assembly Instruction" sheet, and use this product in a safe and proper manner. Especially for children, parents or an instructor should teach the children the proper manner in which to use the device. To prevent against accidents and injury Please follow the cautions listed below Caution (including danger, or warning). This mark indicates cautions in which you should pay close attention to. Acts indicated with this icon are prohibited and should not be attempted. Holder Clamp Leg Connector WARNING If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. Always set the instrument on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the instrument being unstable and overturning. Make sure all bolts are tightened firmly. Loose bolts may result in the rack overturning or parts dropping causing injury. When adjusting the height or angle, do not suddenly loosen the bolt. Please prepare one before starting assembly. 1 2 After removing the unit from the box, remove all cushion material. Setting up the parts Follow the setup order (q~o) in the diagrams shown below. q Temporarily remove the leg connector from pillar (R). w Attach center pipe (D) to pillar (R) and pillar (C), and secure. e Reattach the leg connector. r Attach the cross pipe to the leg connector. t Attach center pipe (C) to pillar (L) and pillar (C), and secure. y u i o Attach center pipe (B) to pillar (R) and pillar (C), and secure. Attach center pipe (A) to pillar (L) and pillar (C), and secure. Attach the module holder to pillar (L), and secure. Attach the cymbal holders and tom clamps to the holder clamps, and secure. Cymbal Holder (CH740) Tom Clamp (CL-940A) Cymbal Holder (CH745) Caution : Make sure the bolts marked with a " Piller (L) Center Pipe (A) " are loosened before setting up. Cymbal Holder (CH740) Piller (C) i Holder Clamp Tom Clamp (CL-940A) Holder Clamp Holder Clamp Center Pipe (B) Piller (R) o o o Tom Clamp (CL-940A) Module Holder u t Holder Clamp o o o $ Caution Center Pipe (C) y Leg Connector q Remove temporarily. [. . . ] e Tighten knob of leg connector Holder Clamp w Leg (L) Leg (C) Center Pipe (D) Cross Pipe r Memory Clamps Holder Clamp Using the memory clamps let you obtain the same height setting for all future setups. Leg (R) Leg Connector Optional Parts Pad and Drum Trigger Grouping q DTXTREME IIS Drum Trigger Module Set up example e PCY150S Cymbal Pad w PCY130/130S Cymbal Pad r RHH130 Real Hi-hat Pad Satellite Speaker PCY130S Satellite Speaker w q t TP100 Drum Pad y TP120SD Drum Pad o Snare Stand *SS652 etc. PCY150S e w PCY130 !0 Hi-hat Stand *HS-740 etc. t t u KP65 Kick Pad i Foot Pedal * DFP-9310 etc. u y r Monitor System and Attachement Grouping · SPAT1 (1 set L/R units) · CYAT150 · TPCL150 !0 o i · MS50DR · Sub Woofer · Satellite Speakers amp unit · MS100DR · Sub Woofer amp unit Sub Woofer amp unit · Satellite Speakers 3 Attaching the DTXTREME IIS 3-1 Remove the module holder from the holder clamp, and use the supplied screws to attach the DTXTREME IIS. Make sure only the supplied screws are used. Using any other screws may result in the unit falling off the holder or damage. 4 Attaching the cymbal pads Attach the cymbal pads to the cymbal holders and adjust their position, then secure in place. [. . . ]