User manual YAMAHA RX-V361

[. . . ] G RX-V361 AV Receiver Ampli-tuner audio-vidéo OWNER'S MANUAL MODE D'EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING GEBRUIKSAANWIJZING CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. Caution: Read this before operating your unit. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this sound system in a well ventilated, cool, dry, clean place ­ away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit. [. . . ] If the EON indicator is not lit in the front panel display, select another Radio Data System program so that the EON indicator lights up. EON 3 Press I EON on the remote control repeatedly to select one of the 4 Radio Data System program types (NEWS, AFFAIRS, INFO or SPORT). The name of the selected program type appears in the front panel display. NEWS Lights up y To cancel the EON feature, press I EON on the remote control repeatedly until the name of the program type disappears and "EON OFF" appears in the front panel display. English 39 En RECORDING Recording Recording adjustments and other operations are performed from the recording components. Refer to the operating instructions for those components. Notes · When this unit is set to the standby mode, you cannot record between other components connected to this unit. · The settings of TONE CONTROL (see page 29) and VOLUME settings, speaker levels (see page 29) and the sound field programs (see page 31) do not affect recorded material. · The source connected to the MULTI CH INPUT jacks of this unit cannot be recorded. · Digital signals input at the DIGITAL INPUT jacks are not output at the analog AUDIO OUT (REC) jacks for recording. Therefore, if your source component is connected to provide only digital signals, you cannot record the source. · A given input source is not output on the same OUT (REC) channel. · Once you have connected a recording component to this unit, keep the component turned on while using this unit. If the component is turned off, this unit may distort the sound from other components. · Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright laws. y Do a test recording before you start an actual recording. If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture itself may be disturbed due to those signals. 1 2 Turn on all the connected components. Press D INPUT l / h repeatedly (or press one of the input selector buttons (C)) to select the source component you want to record from. 3 4 Start playback on the selected source component or select a broadcast station. Start recording on the recording component. 40 En Set menu Set menu You can use the following parameters in set menu to adjust a variety of system settings and customize the way this unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening environment. Basic setup BASIC SETUP Use this feature to automatically adjust speaker and system parameters (see page 21). Manual setup MANUAL SETUP Use this feature to manually adjust speaker and system parameters. Sound menu 1 SOUND MENU Use this menu to manually adjust any speaker settings, alter the quality and tone of the sound output by the system or compensate for video signal processing delays when using LCD monitors or projectors. Parameter Features Selects the size of each speaker, the speakers for low-frequency signal output, the crossover frequency, and the location of the front speakers connected to the FRONT B terminals. Adjusts the output level of each speaker. Adjusts the tonal quality of the center speaker. Adjusts the output level of the LFE channel for Dolby Digital or DTS signals. Adjusts the dynamic range of Dolby Digital or DTS signals. Adjusts the muting level, audio delay settings, maximum volume level and initial volume level. Page 43 44 45 45 45 45 46 A)SPEAKER SET B)SP LEVEL C)SP DISTANCE D)CENTER GEQ E)LFE LEVEL F)D. RANGE G)AUDIO SET ADVANCED OPERATION Input menu 2 INPUT MENU Use this menu to manually reassign the input jacks, select the input mode or rename the input source. Parameter Features Assigns the input jacks of this unit according to the component to be used. [. . . ] 11 Playing video sources in the background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 POP M, Radio Data System program type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Pop/Rock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 PRESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]